Ancel AD600 OBS2 Scanner Multi-Systems Scan & Diagnostic 

1.Engine System

Quickly determine the cause of the Engine System, and turn off the warning light. It also retrieves current, permanent, and pending codes in the vehicle engine system, What's more, it also shows critical OBD II standard extended data, such as fuel, emissions data, and other real-time manufacturer-specific parameters in the engine system for making sure it works correctly and safely.

2.SRS(Airbag) System 

When the SRS (Safety Restraint System) light is on, it means that the Airbag Control Unit sees an issue in the system. The system is subsequently disabled and the airbags will not deploy in the event of an accident. You can use AD600 to check if there is a malfunction in the SRS system and get it fixed. It is very important that airbags are functioning properly at all times.

3.TPMS System 

If the TPMS (Tire Pressure Monitoring System) light is illuminated, it means your tires could be underinflated, which can lead to undue tire wear and possible tire failure. AD600 can read codes on the TPMS system to identify possible problems including a bad sensor or underinflation and clear them when a solution is found.

4.ABS System 

When you see the ABS (Anti-lock Brake System) light is on, you know it’s serious. AD600 can help. Just use it to identify what has gone wrong by plugging in the unit to your 16-pin port (normally under your steering wheel). You can make a determination what could be the causes of the error: low brake fluid, a blown fuse, or abnormal signals from wheel sensors.

5.Transmission System

If you notice the following: transmission slipping, rough shifts, delayed engagement, fluid leak or transmission warning, then your car may need to be maintained. You can use AD600 to do a series of diagnostics and pinpoint the problem area for repair.

 6.SAS System 

The steering angle sensor (SAS) is a critical part of the ESC system that measures the steering wheel position angle and rate of turn. SAS is very important for the safety of the driver and the passenger alike. When the SAS light is on, you can use AD600 to read error codes. Once a problem is fixed, you can use AD600 to recalibrate and clear the codes.

7.ESP System

Electronic Stability Program (also Electronic Stability Control) can improve a vehicle's stability by detecting and reducing loss of traction (skidding). When ESP detects a loss of steering control, please check the ESP light and get a code reading before you do anything about it. It can help you to minimize potential losses, both monetary and in terms of human life.

 8.Battery System

The battery light (a light in the shape of a battery symbol) indicates a battery charging problem. If the battery light comes on and stays on while you are driving, the most common cause is a broken alternator belt. You can use AD600 to read the fault code and clear it when the problem is located.

9.Immobilizer System

The immobilizer warning light turns on if your anti-theft system does not recognize the car key being used, or if it's the wrong key or low on battery. The engine may start and run for a few seconds before dying or the engine may not even crank up at all. AD600 can assist you by reading error codes associated with the above-mentioned symptoms.

Ancel AD600 OBD2 Scanner Fit for VAG Group Vehicles (for VW, for Audi)

1.Oil Service Reset

Sometimes shops neglect to reset the maintenance-required meter if the light doesn't happen to be on yet when they are changing the oil. Many quick-lube shops simply don't know how to reset it. OBD2 scanner oil reset comes on strictly as a function of those miles can through maintenance-required light comes on to remind you to change your oil.

 2.TP Position Check

The TPS connects to the throttle plate on the throttle body. The position sensor has a variable resistance potentiometer that sends a varying voltage signal to the Power Control Module (your car's engine computer) according to the position of the throttle plate. With the engine running, the position of the throttle plate (along with other sensors) tells the computer how much fuel the engine needs at any given moment. OBD2 scanners correct signal coming from the TPS, remind you begin to notice drivability problems.

 3.EPB Brake Pad Reset

Electronic handbrake is a technology that realizes parking brake by electronic control. Unlike the traditional handbrake where the driver pulls the level, in EBP the driver presses a switch. The switch then sends a command to electronic brake module. The module senses that the parking brakes need to be operated then sends a command to actuators in the brake calipers. ANCEL code reders a trick to save you money and time.

 OBDII Basic Function