The 1966 Danelectro DS 100 Piggyback Tube Amplifier Head is a unique and sought-after piece of vintage equipment. It’s the builder-branded version of the Silvertone Model 1485, and while they refer to the same circuit as a tremolo on one amp and a vibrato on the other, the DS100 and the 1485 share many similarities, and the schematic is almost identical.
This is a head-only amplifier and is in excellent Player Grade condition, rated at 100 watts, and features a distinctive combination of vibrato and the unusual sounding reverb common to the Danelectro/Silvertone amps.
The DS100 uses a split chassis design and features nine tubes: three 12AX7s, two 6FQ7s, and four RCA 6L6s. It has two separate channels, each with two inputs: On Channel 1 a volume, bass , and a treble control. On channel 2, you’ll also find the reverb, vibrato strength, and speed. The front lower panel includes a standby/operate switch, power on/off switch, ground switch and power indicator light. The original power transformer has NOT been replaced - it has been re-painted.
All of the old electrolytic caps have been replaced with CE, Sprague or F&T caps as well as any marginal drifted resistors. It has not been over-restored - any working in-spec resistors and bypass caps were left in place. A 3-wire grounded power cable has been fitted, the death-cap removed, and the unnecessary ground switch disconnected. Switching 1/4” input jacks (Fender style hi/lo input & auto grounding) have been installed. (See the chassis images) This amp takes pedals extremely well, and sounds fantastic through a stereo cab. Jump the two input channels and you get more great drive. It is in excellent working order. Both channels are strong. Dimed it gives a great crunch - especially with a hum bucker. Also included is an original dual foot switch that controls the tremolo and reverb.
The octal speaker connector has been removed and a second 1/4” speaker jack fitted to accommodate the amp’s unique speaker output. The original Danelectro 6 x 10” speaker cab used two separate sets of three speakers, each driven by a separate output transformer. This DS100 has been adapted to use two speaker outputs. It’s important to note that two separate speakers are required when playing the amp. The circuit uses two output transformers, The 2 output transformers are Identical to the ones that are in the Silvertone 1484 amps: they have 2 windings - a 2.66 ohm output when driving three 8 ohm speakers (like the original 6X10 cab that came with this head - each tranny driving 3 speakers) and a 4 ohm output when driving a single 4 ohm or two 8 ohm speakers wired in parallel.
I wired the 4 ohm windings of each OT to the 2 output jacks. IMPORTANT - connecting only one speaker will damage the transformer that you don't use. A suggested setup would be a 2x 8 ohm speaker cab (4 ohms), a 4 X 8 ohm stereo cab (2 inputs at 4 ohm) or two separate 4-ohm speaker cabs.
The amp has been cleaned inside and out. All loose covering re-glued. The cosmetic condition is very good, it has some blemishes and marks - but no tears or ripped corners. The faceplate is in very good shape with some minor pitting on the metal and all the original knobs are in great shape.
This is a great sounding, excellent example of this iconic garage band amp and should be trouble free for another 50 plus years.
(Note: the 2X12 Mid Century Audio tweed extension speaker in the images is not included in this sale).
Dimensions: 16-1/2“W x 13"H x 6"D 22 lbs.
Shipping weight - 35lbs.
For exact shipping cost please request a quote with your city and zip code.
The amp will be shipped with the tubes removed, bubble wrapped and placed in their own box. The head will be bubble wrapped, placed in a box and then double-boxed with crush zone for protection for shipping. Local pickup also available.