LavaTap 2.4 Litre Replacement Boiling Water Tank, Filter Kit and 1/2" Adaptor

A 2.4 litre replacement boiling water tank for LavaTap 3-in-1 and 4-in-1 boiling taps, supplied with a filter kit and one 3/8" BSP female to 1/2" BSP male brass bush. If your tank has failed, you can keep your tap, and you start with a genuine filter from day one. The brass bush converts one of the tank's 3/8" BSP male connections for a tap hose with a 1/2" female end. No washer is included, so reuse your seal and check the threads first.

Up to 60 cups an hour

Up to 1.7 litres of water at up to 98 °C on demand, and up to 60 cups an hour for tea, coffee and cooking. Choose from 14 settings between 45 and 98 °C on the digital display. It reheats automatically, with a 1.5 kW element and a thermal cut-out, and it is insulated and quiet in the cupboard.

Which tank do I need?

This pack is for a tap hose with a 1/2" female end, as on ProBoil 2X and Bristan taps, and it includes the filter kit. If your tap hoses have 3/8" BSP ends, choose the LavaTap boiling water tank. If your tap is plumbed with 6 mm push-fit tube, as on Ellsi, ETAL and Sauber taps, choose the LavaTap tank with 6 mm push-fit adaptor. Already have a genuine filter fitted? Choose the LavaTap tank with 1/2" adaptor. Not sure which one you need? Send us a message with a photo of your tank's connections and we'll tell you.

In the box

2.4 litre boiling water tank with 13A plug lead, a filter kit (filter head and first cartridge), and one 3/8" BSP female to 1/2" BSP male brass bush. Tap, isolation valves, pressure-reducing valve and other connectors are not included.

The filter

An anti-scale carbon filter for scale, chlorine and odour, rated for 1.5 to 5 bar, with 1/4" (6.4 mm) push-fit tube connections. The filter head and first cartridge are in the box. Change the cartridge at least every 6 months, or sooner in hard water, with a genuine filter, and keep the receipts.

At least 2 years with the full kit

Buy the LavaTap tap, tank and filter together as a full kit and every part is guaranteed for at least 2 years, as long as it is fitted by a qualified installer, you register within 30 days of installation, you change the filter at least every 6 months with a genuine filter, and you follow the other guarantee terms.

Your guarantee

The heating element is covered for 5 years and the sensor and control board for 2 years, from installation. Register within 30 days of installation, using the guarantee card in the box, because your cover is not active until you do. Cover is for manufacturing faults in normal domestic use, held by the original buyer, and your statutory rights are unaffected.

Keeping your cover valid

Have the tank fitted by a qualified installer, working to current regulations, with genuine parts throughout. Fill the tank and run the tap until the flow is steady before you plug it in. Hand-tighten the 3/8" BSP connections, because a spanner can crack the internal seals. Install it indoors (0–35 °C), upright and uncovered, with 10–15 cm clear on three sides. Keep the water pressure between 1.5 and 5 bar, and keep the vent pipe free of kinks. Change the filter at least every 6 months with a genuine filter, and keep the receipts.

Not covered

Incorrect or DIY installation, dry-fired elements, limescale and hard-water damage, frost damage, non-genuine parts or filters, missed filter changes, general wear and tear, and harsh or abrasive cleaning.

Specifications

Capacity 2.4 litres, up to 1.7 litres instant draw-off, up to 60 cups an hour. Reheat time: about 7 minutes after drawing off 1.7 litres, and about 10 minutes to heat a full tank from cold (approximate, from a 10 °C supply). Power 1.5 kW, 230 V, 13A plug, 110 cm lead. Temperature 45–98 °C with 14 settings. Tank connections 3/8" BSP male. Adaptor 3/8" BSP female to 1/2" BSP male brass bush. Filter connections 1/4" (6.4 mm) push-fit tube. Size 240 W x 330 H x 220 D mm. Water pressure 1.5 to 5 bar. IPX4.