Obtain the desired airbrush effect.
The video provides detailed step-by-step instructions for replacing an airbrush accessory, including removing the tailstock, loosening the set screws, removing the old part, and installing the new accessory.
When cleaning the airbrush, use pen wash liquid to pour into the paint pot and plug the nozzle, while gently pulling the trigger position appropriately to allow the liquid to flow back inside the airbrush to prevent excess liquid from spilling out. Or you can use the method of loosening the pen pressure cap to let the liquid flow back to achieve the purpose of cleaning!
The first thing to check airbrush gun's needle. If the screws not installed tightly, the pen needle will not retreat.Just tighten this needle and it will be work.
Another situation is that the spray will only bubble after receiving water, we need to check the previous section-pen pressure cap. If it is not tight, we need to use this wrench to hold it tight.
We need to check the caliber of the components matches. Don't make a mistake with the caliber of nozzle, nozzle cap and needle. It can only be used if it is installed with the same caliber.
When you want to change a different caliber nozzle and can't remove the nozzle. Do not press it in front, as squeezing it will cause the nozzzle to deform. Just insert the end of the wrench and gently tap or pry it to loosen the nozzle. Related vedio are uploaded in front page.
Problems may caused by not tightening the nozzle pressure cap, which may prevent spraying or cause backflow, resulting in continuous bubbling of the paint cup. After replacing the accessories, the pressure nozzle cap needs to be tightened a bit.
1. If you find paint won’t come out of the machine sprayer or airbrush not working properly, Why has this happened?
Problems may caused by not tightening the nozzle pressure cap, which may prevent spraying or cause backflow, resulting in continuous bubbling of the paint cup. After replacing the accessories, the pressure nozzle cap needs to be tightened a bit.
2. Spray gun leaks from around the trigger & from behind the paint housing. Why has this happened?
The tail connection of the spray gun is not fully tightened. All accessories must be confirmed to be tightened before use and tested with water first.
3. If you have clogging issue, there is the problem of "no water out of the air", Why has this happened?
The airbrush were used but not cleaned thoroughly, the outlet may be blocked by dried paint. Gently pull out the needle and wipe the needle clean with a paper towel. Put the needle back where you found it and tighten the hat. Try again the effect.
4. What type of paint is the airbrush suitable for？
If the paint is water-based paint, it will be suitable for our airbrush set. The water-based paint is easy to clean-up. The solvent based paint would melt all the plastic parts or swell the handle and other rubber parts.
5. How to use wrench to change tight nozzle when you want to change a different caliber nozzle?
Do not press it in front, as squeezing it will cause the nozzzle to deform. Just insert the end of the wrench and gently tap or pry it to loosen the nozzle. We also uploaded related vedio about how to change the nozzle and needles in detail page.
All parts of the airbrush gun are marked for you to use better. You can also refer to the manual.
The airbrush set comes 3 tip sizes of jet needles and nozzles (0.3mm/0.5mm/0.8mm), 2cc/5cc/13cc paint cup. Equipped with 1/8~1/4 fast joint and 70.87 inches mesh air hose, spraying more convenient. 15-50 psi working pressure. AIR COMPRESSOR IS NOT INCLUDED.
The airbrush set comes 3 tip sizes of jet needles and nozzles (0.3mm/0.5mm/0.8mm).
Set screw which is in front of the airbrush trigger can adjust the air outlet size.
Adjusting screw on the tail of the airbrush can change the atomization size.
The airbrush set comes 3 tip sizes of jet needles and nozzles (0.3mm/0.5mm/0.8mm).