2PCS Oxygen Sensor For 2015 -2019 Mercedes-Benz GLA45 AMG GLA250 CLA250 B250

Specification:

This Oxygen O2 Sensor is a new, aftermarket replacement part that has the following specifications:

Direct Fit
Correct Connector No cutting or splicing
OE/OEM Part Number:234-5158,0095425518, 0095425618, 0095425918, 0095426018, 0095426318, 226935DC0A, 22693HG00C
234-4839,0075426318, 226A05DD0A
Line length:550mm+350mm
4 +5 wire configuration.

Compatibility :

FOR

INFINITI
QX30 2.0L L4 Turbocharged 2017 2018 2019

Mercedes-Benz
B250 2.0L L4 Turbocharged 2013 2014 2015 2016 2017 2018 2019
CLA250 2.0L L4 Turbocharged 2014 2015 2016 2017 2018 2019
CLA45 AMG 2.0L L4 Turbocharged 2014 2015 2016 2017 2018 2019
GLA250 2.0L L4 Turbocharged 2015 2016 2017 2018 2019 2020
GLA45 AMG 2.0L L4 Turbocharged 2015 2016 2017 2018 2019
Metris 2.0L L4 Turbocharged 2016 2017 2018 2019 2020

Features:

Porous PTFE Filter - Allows atmospheric oxygen to enter the sensor without permitting water or engine contaminants to seep into the casing.
Double Protection Cover - Maintains proper unit temperature for quicker response times and protects the ceramic element against silicone and lead poisoning.
Stainless Steel Housing - Resists corrosion and contamination with a rugged, watertight body.
Aluminum-Oxide Trap Layer - Keeps silicone and lead outside the ceramic elient through, preventing damage to the platinum electrode.

Where is the oxygen sensor in your vehiche?

Whow to install an oxygen sensor?

1.Locate the oxygen sensor on your vehicle by looking for a part that looks like a spark plug that sticks out from the exhaust pipe. It will have an electrical connection attached to it.

2.Disconnect the electrical connection on the oxygen sensor. Use a flat tip screwdriver to push in the tabs and pull the connection apart.

3.Unscrew the oxygen sensor off the exhaust pipe using either an open-end wrench or a special socket made to remove it. The majority of oxygen sensors will take an SAE 7⁄8 inch (2.2 cm) wrench.

4.Compare your new oxygen sensor to the old one. If the new one did not come with an electrical connection, but just with the wires stubbed out, you need to do a little work.

· Cut off the old connector from the bad oxygen sensor, strip the wires and solder the wires to the new oxygen sensor. You can also use butt connectors.

· Use heat sensitive shrink tape to seal the connections.

· Follow manufacturer's instructions to know which wires to tie together.

5.Reverse the steps used in removing the oxygen sensor and install the new part.Add a small amount of anti-seize to the threads of the new sensor. Screw it in place clockwise and snug it down with the socket or open-end wrench. Do not over tighten the sensor as you might strip the threads.

6.Plug the electrical connections back in.

7.Turn on the ignition key, but do not start your vehicle. Use the diagnostic scanner/reader to clear the code from the vehicle's computer.

8.Start the car. You should notice an immediate improvement.

NOTE:

If you can't determine whether the oxygen sensor fit your vehicle or not, please contact us.

Payment Policy
Shipping Policy
Returns Policy

Payment Policy

We accept Paypal only for the payment, and all orders should be paid through Ebay auction, please do not pay directly to our Paypal account.

Paypal allows to pay by Credit Card, Direct Debit, VISA, eCheck, or other methods, please kindly check Paypal for more information.

For multiple purchases, please add items to your Ebay shopping cart and pay once for entire order.

Shipping Policy

We would send out within 2 business days usually . If there is any delay, you will be notified immediately via e- mail .

l Items will be shipped to buyer's eBay registered address. Please confirm your address before making payment.

l We will NOT be responsible for any delay during delivery including but not limited to customs postage checking, strike, force majeure etc

Returns Policy

Out 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. In addition , it allows customers to return new and unused products in their original factory condition for any reason within 30 days from the date of purchase.

Notice:

1.All returns must be pre-approved by Autopartm and have a return merchandise authorization (RMA) number.Unauthorized returns will not be accepted.

2.Buyers are responsible for appropriate packing, returning shipping cost, insurance and returning the item in “new” condition. Used items will not be accepted for return.

3.We will replace the returning item with an identical item, issue a full store credit or a full refund.

There is a difference between Genuine and OEM / OE Supplier brands. A genuine part is a part in the auto manufacturer’s original box with their logo on the box. OEM / OE Supplier is a brand licensed by the vehicle manufacturer and the part will not come with the vehicle manufacturer’s logo on it. OEM / OE Supplier parts are often the same parts you’d get at the dealership, just in a different box. We do not accept returns based solely on where a part is manufactured.

Store Categories