MEGAWARE KEELGUARD USA-Made, Original DIY Keel Protector, 11ft Black

Key Features

• Boat Keel Protector - Protect your boat keel from sand, rocks, oyster beds, concrete ramps, and everyday wear and tear on the water with The Original Do-It-Yourself Keel Guard from Megaware. Note: compatible with fiberglass and some aluminum boats
• Easy to Install - The boat protector features an exclusive self-sealing contoured edge that creates a clean, tight seal; no messy sealants needed. Easy install in 4 simple steps; etch, clean, prime, apply!
• Superior Engineering - This patented hydrodynamic drag reduction design is produced using the highest quality materials and 3M premium adhesives. Pliable and tough, the 5-inch wide boat keel protection easily conforms to your boat's keel; it’s shock absorbing, exclusive contoured edge design, and drag reduction channels won't slow your boat down
• 9 Standard Length Kits - Our boat keel guard comes in 9 different sizes that range from 4 to 12 feet long to ensure you have the correct size; shields come in 12 colors that will not fade or dull while enhancing the look of your boat. Note: if the size of your boat falls between 2 sizes, order a size up for additional keel protection
• Lifetime Warranty - The Megaware KeelGuard is so tough and reliable that we include a lifetime warranty during normal use of your boat, for as long as you own your boat

Additional Product Details

Prevent damage and eliminate costly repairs by protecting your keel against abrasive sand, rocks, concrete ramps, and oyster beds

Hydrodynamic drag reduction design features self-sealing contoured edges and uses the highest quality materials and 3M premium adhesives

Protect your vessel against abrasive wear during normal use for as long as you own your boat!

Frequently Asked Questions

Can I Install a KeelGuard on a Kayak or Canoe? Because most kayaks and canoes are made out of low-surface energy plastics, our Keelguard is not compatible with either as the 3M adhesive doesn't bond to LSE plastic

Can I Install a KeelGuard on a Jet Ski, Ski-Doo, Wave Runner, or Other Personal Watercraft (PWC)? Our KeelGuard is not compatible with modern hull designs and must be installed 4-6 inches above the resting water line

Can I Install a KeelGuard on a Catamaran? The KeelGuard is not compatible with most Catamarans due to having very sharp keels with a steep 90° upturn. Please call Megaware directly if you have questions about your Catamaran

Can I Install a KeelGuard on an Aluminum Boat? The KeelGuard can be installed on some aluminum boats. If your boat has a raised or reinforced center keel, it cannot be raised higher than 1/4 inch. The center keel cannot have any reinforced welding around the edge, rivets, or sharp angles. If you have compatibility questions, please contact Megaware directly. Not compatible with: Lund, Alumacraft, Smoker Craft, Crestliner, or Tracker

Can I Install the KeelGuard on a Pontoon Boat? The KeelGuard cannot be installed on the bottom of pontoon tubes. For the side of pontoon tubes, we recommend the Pontoon Guard

Can I Apply the KeelGuard Over Strakes or Chines? Yes, the KeelGuard can be applied over slightly raised strakes and chines. NOTE: must apply sealant over strakes/chines areas to seal off gaps and prevent water from getting under the adhesive

Can I Apply the KeelGuard Over a Vinyl Wrap? The KeelGuard is not recommended to install over boat wrap. Must be installed on the actual surface of the boat. We do not recommend installing the KeelGuard over a vinyl wrap because it will pull the wrap off the boat

Can I Apply the Megaware KeelGuard Over Boat Bottom Paint or Anti-Fouling Paint? Anti-fouling or boat bottom paint must be removed prior to installing the KeelGuard. You can apply boat bottom or anti-fouling paint OVER the KeelGuard once you have installed it to the actual surface of the boat

Specifications