Note: Please send your Vehicle VIN# to us first，we can help you confirm the part whether fit your vehicles.
Technical Details:
Component Type: Combination Switch Reel / Clock Spring
Interchange Number: 77900TA0H12
Terminal Type: Multi-pin (Please verify with your original unit)
Installation Position: Steering Column
Package Included: 1 x Spiral Cable Clock Spring ( without Angle Sensor，without Heated Steering Wheel）
Fitment & Compatibility:
for Honda Accord 2008-2012 EX, EX-L, LX-S, SE, HFP (L4 & V6 Engines, Coupe & Sedan)
for Honda Odyssey 2011-2013 EX, EX-L, Touring, Touring Elite （Requires VIN Verification，This unit does NOT support vehicles with
memory steering or complex telematics options typically found in Touring trims）
for Honda Pilot 2009-2012 EX, EX-L, Touring,SE（Special Edition）（Requires VIN Verification，This unit does NOT support vehicles with memory
steering or complex telematics options typically found in Touring trims）
for Honda Crosstour 2010-2015 EX, EX-L (All Trims)
for Honda Insight 2010-2014 EX, Base, LX (Requires Audio Control Verification)
for Honda CR-Z 2011-2015 Base, EX, Premium (All Trims)
Installation Guidance:
please message us your VIN (Vehicle Identification Number) before ordering.
NOTICE: To ensure longevity and prevent damage to the internal ribbon cable:
Center Position: This part is shipped in the centered position. Please do not manually spin the reel before it is fully mounted.
Professional Install: We strongly suggest installation by a qualified technician to ensure correct alignment and connection.
🚨 FITMENT & COMPATIBILITY NOTICE 🚨
(READ BEFORE PURCHASE)
The eBay compatibility chart (Fitment) is for reference only and may not be 100% Accurate for your specific trim. Subject to the ebay message we send you.
The ONLY way to guarantee fitment is to match the exact OE Part Number from your original unit with the interchange numbers listed above.
If you are unsure, please send us your VIN (Vehicle Identification Number)\ OE number \Photos of original accessories (front and back and slot plugs) via eBay Messages prior to purchase, and our team will verify fitment for you!
⚠️ CRITICAL INSTALLATION WARNING:
1. Point the front wheels STRAIGHT AHEAD before removing the old clockspring.
2. DO NOT remove the plastic locking pin/clip on the new clockspring until it is fully installed and the steering wheel is properly aligned.
3. Improper installation, turning the steering wheel before the installation is complete, or failing to center the wheels WILL SNAP the internal ribbon cable instantly.
*Note: Professional installation is highly recommended. Damage caused by improper installation or buyer error is not covered under warranty and will void the return policy.
💡 FAQ & Troubleshooting (After Receiving Your Package)
-
1. Airbag/Fault Light ON or OBD Errors?
This is completely NORMAL after replacing a clockspring. You must manually clear the fault codes using an OBD scanner to turn off the light.
-
2. Pins/Connectors don't match?
Please contact us first! Your original clockspring likely has an integrated Angle Sensor. You simply need to transfer (transplant) your old angle sensor to our new clockspring.
-
3. Think it doesn't fit? DO NOT OPEN A DISPUTE.
If you encounter any fitment issues, please do not open a return or case immediately. Send us a message! We will solve the problem for you in the fastest time possible.
-
4. Need help with Angle Sensor Transfer?
If you do not know how to transfer the angle sensor, please contact us for guidance, or we highly recommend seeking a local certified mechanic for professional installation.
🔧 INSTALLATION & TRANSPLANT GUIDE
▶ General Clockspring Installation Steps
▶ Angle Sensor Transplant Tutorial
Step 1:
Step 2:
Step 3:
