Strymon Deco V2 Tape Saturation & Doubletracker Effects Pedal

Tape saturator pedal offering a range of tonal options

Add warm dimensionality and luscious tape saturation to your signal. Teleport the tones of yesteryear to your board. Effortlessly create a huge range of beautiful, distinctive, and enveloping vintage sounds. From the inherent warmth and luscious tape saturation to the forgotten art of how these machines were manipulated, Deco brings this original inspiration back, giving you these vintage tape effects from the earliest recording studios, right on your pedalboard.

Deco's Tape Saturation smooths out your sound with familiar and delicious tape compression and saturation, while fattening your tone with subtle tape-driven transparent overdrive.The Doubletracker provides the power to shift your sound in many ways, easily allowing you to achieve syrupy slapback tape echoes, psychedelic tape flanging, and gorgeous tape chorusing sounds.
Our second generation Deco gives you the same gorgeous reel-to-reel tape sounds from our original, while adding several significant new features, incorporating technological advancements, hardware improvements and design enhancements to give you additional flexibility, power, and ease of use on stage and in the studio.

Full MIDI implementation means you can control just about every switch, knob, and setting remotely by sending MIDI commands from your controller or DAW via Deco's EXP/MIDI jack or USB-C connection. Lag Deck delay time can be synchronized via MIDI Clock Sync, and the sync setting can be saved for each preset. 300 MIDI preset locations are available for loading and saving your favorite settings.

Deco now comes with an all-new cassette tape voicing that employs an auto level control (ALC) process common to many high-end cassette tape recorders, resulting in a compressed, fat tone. In addition, a new dedicated Tone knob lets you adjust the tone of the Tape Saturation exactly to your liking, from dark to bright.

A premium analog JFET input circuit ensures superb responsiveness to your playing, and you can select mono or stereo input with the flick of a rear panel switch. All this, plus a new ARM DSP chip provides more processing power for every sonic nuance, with less energy consumption on your pedalboard.

Features

High impedance ultra low-noise discrete Class A JFET TRS stereo input.

Low impedance independent TS stereo outputs.

Expression pedal input allows the connection of a TRS expression pedal, MiniSwitch, MultiSwitch Plus, or TRS MIDI connection.

USB jack for controlling via MIDI from a computer or for performing firmware updates.

Dedicated tap tempo & On/Off footswitches

Premium JFET analog front end

Ultra low noise, high performance 24-bit 96kHz A/D and D/A converters provide uncompromising audio quality

520MHz ARM Superscalar processor

32-bit floating point processing

20Hz to 20kHz frequency response

Audio Input Impedance: 1M Ohm

Audio Output Impedance: 100 Ohm

Strong and lightweight anodized dark gray aluminum chassis

Power requirements: maximum 9 volts DC center-negative, with a minimum of 300mA of current

Dimensions: 4.5" deep x 4" wide x 1.75" tall (11.4 cm deep x 10.2 cm wide x 4.4 cm tall)

Designed and built in the USA

Features

• Hand crafted dTape algorithms deliver vintage recreation of analogue reel to reel tape effects
• FX include deliciously compressed/transparently overdriven tape saturation, plus doubletracking FX (syrupy slapback and longer (up to 500m/s) warm tape delays, gorgeous tape chorus, psychadelic tape flanging)
• The tape saturation and doubletracker circuits sections are independent - two pedals in one!
• Independent control of (i) tape saturation level and decks'' output volume (ii) reel to reel lag time + reel varispeed (''wobble'')
• Blend (of 2 tape decks) control and three Doubletracker blend types (Sum, Invert, Bounce) to individually tailor your effects
• Secondary controls allow control of High Trim, Low Trim, Auto-Flange Time, Wide Stereo Mode and +/- 3dB Boost/Cut
• Hold down the bypass switch for a studio-inspired through-zero auto-flange!
• Two signal routing modes: Standard and Wide Stereo
• Expression pedal input with selectable control over any knob parameter
• TRS stereo input (with stunning new JFET preamp) and output, plus MONO/STEREO input switch on the back of the unit
• Full MIDI control, MIDI clock sync and 300 presets
• USB port for updates and MIDI over USB
• TRS MIDI jacks: allow bi-directional MIDI communication with a single cable using the Conduit interface
• Editor/librarian support via USB

Specifications