Replacement For FF63017NN and FS53029NN Fuel Filter Combination Replaces 7 Micron 16403EZ41A 12 Micron 16403EZ40A

 

Product Description

Fitment:Replacement For FF63017NN and FS53029NN Fuel filter For 2016-2019 Nissan Titan XD 5.0L V8 Diesel Engines.

Replacement Part Number:

Upper engine filter:Replacement For 4335493,4378483,16403EZ41A,FF63017NN,WF10442,PF46140.

Frame rail filter:Replacement For 4360105,4335492,16403EZ40A,FS53029NN,WF10441.

Feature:Prevents fuel problems and helps prolong the life of your engines fuel injection system.Provide high flow rates and superior filtration efficiency with a premium filtration media to help improve engine performance.High dirt holding capacity of filter elements through high filter surface area.

Package includes:1 x FF63017NN fuel filter(7 Micron),1 x FS53029NN fuel filter(12 Micron)

Warm Hint:Please replace the filters regularly to keep the engine in good condition.

 

Fitment

For Nissan Titan XD PRO-4X 2016-2019 5.0L V8 Diesel Engine

For Nissan Titan XD Platinum Reserve 2016-2019 5.0L V8 Diesel Engine

For Nissan Titan XD S 2016-2019 5.0L V8 Diesel Engine

For Nissan Titan XD SL 2016-2019 5.0L V8 Diesel Engine

For Nissan Titan XD SV 2016-2019 5.0L V8 Diesel Engine

 

Changing frame rail filter

1. Disconnect the negative terminal first, then the positive terminal.

2. Clean the area around the fuel filter to prevent dirt or debris from entering the fuel filter housing.

3. Drain the fuel from water-in-fuel drain.

4. Disconnect the harness connector from the water-in-fuel sensor.

5.Remove fuel filter housing protector.Turn/twist the fuel filter housing counter-clockwise to remove it from the module.

6. Remove the fuel filter element by lifting it straight out of the fuel filter housing.

7.Inspect the fuel filter housing and module for cracks or passage blockages.Replace if damage is found.Inspect the new fuel filter element for the No Filter No Run(NFNR) pin.Replace the filter element if the pin is damaged or missing.

8.Install the fuel filter element into the fuel filter housing and make sure the four tabs are properly seated into the four slots.Install new O-ring on fuel filter housing.

9.Lube the inner seal and o-ring. 10.Install the fuel filter housing onto the module and torque to: 25 N·m (2.6 kg-m, 18 ft-lb).

 

Changing upper filter element

1.Disconnect MAF sensor connector.Disconnect the pressure/temperature sensor.

2.Remove the air cleaner lid and the air inlet air ducts from intake plenum.

3.Cap or wrap the air inlet ducts with suitable material to avoid dirt from entering the air inlet system or engine.

4.Remove the fuel filter lid from the fuel filter housing.Inspect old fuel filter element to verify the inner seal is present.Remove inner seal from inside of the fuel filter housing if inner seal is missing

5.Lube the inner seal and o-ring.

6.Install the fuel filter element onto the standpipe in the fuel filter housing(Do NOT install the fuel filter element into the lid first).

7.Install the fuel filter lid and torque to: 25 N·m (2.6 kg-m, 18 ft-lb).

 

After changing fuel filters

1.Connect the left and right side batteries.Reset customer settings that were lost when the batteries were disconnected.

2.Prime the fuel system.Turn the ignition ON for 90 seconds to prime the fuel system,crank the engine for NO MORE than 30 seconds to start the engine.Once engine does start, it may operate erratically and with increased noise for a few minutes. This is a normal condition as air is being removed from the fuel system.

3.Operate the engine and check for leaks.

JTIyJTNBJTIycGFyYWdyYXBoJTIyJTJDJTIyY2hpb