Injector Sleeve Cup Remover Installer Tool Set 9U-6891 for CAT 3406E C10 C12 C15
Item Description
[Compatible with] Compatible with Caterpillar (CAT) C-10, C-12, C-15, C-16, C-18 and 3406E Engines. (The new puller bridge can be used on all three engines)
[Replaces Part Number] 9U6877 Thrust Bearing, 9U7258 Driver Cap, 221-9778 Puller Stud, 4K-0367 Nut-Full, 5P-8247 Hard Washer, 128-7889 Puller Bridge.
[Quality Assurance] This Injector Sleeve Remover Installer Set is made from quality materials for high precision and durability. And it has undergone rigorous testing and inspection to ensure that all performance parameters are up to the standard, guaranteeing long life.
[Fit] It is comparable in fit, form and function to the part, ensuring proper fit and performance.
[Note] Please check the products as much as possible before purchasing to avoid incompatibility. Please feel free to contact us if you have any questions.
Instruction
Remove the injector sleeves:
1,Clean all spare parts,
2,Install the puller stud into injector sleeve,
3,Install the puller bridge,thrust bearing,hard washer,nut on puller stud in turn,
4,Tighten the nut in order to pull the injector sleeve out of the cylinder head.
5,Remove puller stud from the injector sleeve.
Install the injector sleeves:
1,Clean the bore in the cylinder head,
2,Apply retaining compound to the surface of the injector sleeve (not the cylinder head surface),
3,Lubricate the O-ring with engine oil,
4,Rotate the puller stud into the threads of electronic injector sleeve,
5,Put the puller stud and the electronic injector sleeve in the cylinder head ,
6,Put on driver cap and hit with a hammer to install the electronic unit injector sleeve into the cylinder head.
Remove the injector sleeves:
1,Clean all spare parts,
2,Install the puller stud into injector sleeve,
3,Install the puller bridge,thrust bearing,hard washer,nut on puller stud in turn,
4,Tighten the nut in order to pull the injector sleeve out of the cylinder head.
5,Remove puller stud from the injector sleeve.
Install the injector sleeves:
1,Clean the bore in the cylinder head,
2,Apply retaining compound to the surface of the injector sleeve (not the cylinder head surface),
3,Lubricate the O-ring with engine oil,
4,Rotate the puller stud into the threads of electronic injector sleeve,
5,Put the puller stud and the electronic injector sleeve in the cylinder head ,
6,Put on driver cap and hit with a hammer to install the electronic unit injector sleeve into the cylinder head.
Package Included
1x Puller Bridge
1x Driver Cap
1x Puller Stud
1x Thrust Bearing
1x Hard Washer
1x Nut
1x Driver Cap
1x Puller Stud
1x Thrust Bearing
1x Hard Washer
1x Nut
As pictures show
FAQ:
I purchased by mistake, how do I cancel the order?
Please contact us ASAP. If the item has not been shipped out we can cancel the order for you. If the item was shipped out you can refuse the package and wait for the item to return to us.
I received your item but it does not fit or is defective
Please contact us so we can assist you on the matter.
Buy with confidence
Our quality is based on meeting the requirements of the manufacturer and improvement them in design problems manufacture.
NOTE:
(1)It would be highly appreciated if you might contact us first once you have any problems concerning the items. And you can expect all the issues would be resolved ASAP!
(2)Please let us know before you send us the neutral/negative feedback that wont help to finish the issues. And I will definitely try my best to provide the best solutions which would meet our satisfactory!
(3)According to the distance of the receipt address items would be sent from CA or NJ
(4)This product does not include an installation manual
