Fitment:

Fitment:
For 2007-2013 BMW X5 E70
For 2008-2014 BMW X6 E71 E72

For 2014 BMW X6 M, xDrive35i, xDrive50i 3.0L L6 - Gas, 4.4L V8 - Gas
For 2013 BMW X5 M, xDrive35d, xDrive35i, xDrive50i 3.0L L6 - Diesel, 3.0L L6 - Gas, 4.4L V8 - Gas
For 2013 BMW X6 M, xDrive35i, xDrive50i 3.0L L6 - Gas, 4.4L V8 - Gas
For 2012 BMW X5 M, xDrive35d, xDrive35i, xDrive50i 3.0L L6 - Diesel, 3.0L L6 - Gas, 4.4L V8 - Gas
For 2012 BMW X6 M, xDrive35i, xDrive50i 3.0L L6 - Gas, 4.4L V8 - Gas
For 2011 BMW X5 M, xDrive35d, xDrive35i, xDrive50i 3.0L L6 - Diesel, 3.0L L6 - Gas, 4.4L V8 - Gas
For 2011 BMW X6 ActiveHybrid, M, xDrive35i, xDrive50i 3.0L L6 - Gas, 4.4L V8 - Electric/Gas, 4.4L V8 - FULL HYBRID EV-GAS (FHEV), 4.4L V8 - Gas
For 2010 BMW X5 M, xDrive30i, xDrive35d, xDrive48i 3.0L L6 - Diesel, 3.0L L6 - Gas, 4.4L V8 - Gas, 4.8L V8 - Gas
For 2010 BMW X6 ActiveHybrid, M, xDrive35i, xDrive50i 3.0L L6 - Gas, 4.4L V8 - Electric/Gas, 4.4L V8 - FULL HYBRID EV-GAS (FHEV), 4.4L V8 - Gas
For 2009 BMW X5 xDrive30i, xDrive35d, xDrive48i 3.0L L6 - Diesel, 3.0L L6 - Gas, 4.8L V8 - Gas
For 2009 BMW X6 xDrive35i, xDrive50i 3.0L L6 - Gas, 4.4L V8 - Gas
For 2008 BMW X5 3.0si, 4.8i 3.0L L6 - Gas, 4.8L V8 - Gas
For 2008 BMW X6 xDrive35i, xDrive50i 3.0L L6 - Gas, 4.4L V8 - Gas
For 2007 BMW X5 3.0si, 4.8i 3.0L L6 - Gas, 4.8L V8 - Gas

 

Description:

100% New and High Quality

2 Year Warranty

Item Type: Parking Brake Actuator

Practical secure & durable for not being easy to get worn or corroded

Direct replacement for the old part, saving time and money

No modification required, simple and convenient installation

 
OE Number:
34436850289
34436779451
34436782205
34436785487
34436788556
34436788968
34436796072
34-43-6-850-289
34-43-6-779-451
34-43-6-782-205
34-43-6-785-487
34-43-6-788-556
34-43-6-788-968
34-43-6-796-072
 

Package included:
1 × Parking Brake Actuator with Control Unit

 

Hand Brake Module Installation Manual

Important Notice:
★ It is not allowed to program with automotive diagnostic equipment during loading!!! Programming will not work. ★

 

Installation Steps:

1.Warning: When installing the handbrake module, do not plug in the power plug first.

 

2.Check the brake disc clearance. It is recommended to replace the brake disc if the wear is less than 50% (the thickness of new brake pads is about 7.5mm).

 

3.Install the electronic hand brake to the fixing bracket and lock the screws.

 

4.First, pass the hand brake cable through the rear axle and insert it into the brake caliper slot, ensuring the ball head will not fall out. Secondly, secure it with the limit clip.

 

5.Loosen the gear.

 

6.Install the brake disc.

 

7.Adjust the clearance between the brake pad and the brake disc:

1)Adjust the brake disc clearance and tighten it until the wheels cannot rotate.

2)Adjust 3-4 gears back. At this time, the brake disc may rub slightly. This is normal; the handbrake computer will automatically adjust it.

3)Ensure the clearance is consistent for both wheels.

 

8.Installing disc brake.

 

9.Install the wheel.

 

10.Finally, install the plug, connect to the diagnostic computer, and clear any fault codes.

 

Attentions:

1.The clearance between the brake disc and the brake pad must be adjusted. Failure to do so may result in the following:

2.Different wheel clearances will cause loud noise.

3.Excessive assembly causes the brake module to lock internally and store fault codes (emergency unlocking and mechanical failure). Excessive clearance will lead to cable unhooking at both ends.

 

Final Reminder:

★ It is not allowed to program with automotive diagnostic equipment during loading!!! Programming will not work. ★