- 6-7S Ultra-Fast Bending Speed: This electric rebar bender is designed with excellent performance. It helps save valuable person-hours by bending rebar 1/4'' #2 to 1" #8 Grade 60(6 to 25 mm) within 6 to 7 seconds. Bending Angle: 0-180°, Bending Radius: 1.57'' / 40 mm, Max. Rebar Hardness: HRC30, Item Dimensions(L x W x H): 17.72'' x 19.69 x 20.08'' / 45 x 50 x 51 cm.
- 1700W Pure Copper Coil Motor: This hydraulic bending machine features a 1700W pure copper motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this electric rebar machine's operating life to a large extent. Voltage: 110V, Frequency: 60 Hz, Amps: 14A, Noise: 92 dB(A).
- Angle Adjustment Knobs: This rebar bending machine has two slide-type angle selectors, which can help you accurately bend any angle from 0-180 degrees. Preset angle locks are designed for repeating the same angle bending. When bending processing, the angle of point 1 must be bigger than point 2. Otherwise, the machine can not operate normally.
- Sturdy Machine Body: The electric bender machine adopts a sturdy iron machine body and durable Idler Wheel. Ø78 iron Gyre Idler Wheel and Ø94 Fixed Idler Wheel are stronger and not easy to break. Moreover, it can stand super-hard rebar with strong clamping force, which can help to reduce steel rebar waste.
- Easy to Operate & Transport: This hydraulic rebar bender comes with the standard foot pedal control switch for your easy hands-free bending. With four handles on the corner for you to transport and operate effortlessly. It is widely used in construction engineering for bending rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc.
- Note
- If your shipping address is in Canada, please provide the correct phone number and customer broker information.
- If your shipping address is in the United States, please provide correct phone number.
Key Features
-
6-7 Seconds Bending Speed
The steel rebar bender bends 1/4'' to 1" (6 to 25 mm) steel super fast in just 6 -7 seconds. Bending Angle: 0-180°. The bending speed depends on the thickness of the rebar and the angle you want to reach. Max. Rebar Diameter: 1" / 25 mm #8 Grade 60.
-
Two Angle Adjustors
Adjust the angle you need by moving left or right, and after angle adjustment is set accurately, ensure that the angle setting handle is fixed. When you find some abnormal during the operation, you must press down emergency stopped to close down the machine's operation.
-
Iron Idler Wheel
The high-strength Ø78 Gyre Idler Wheel and Ø94 Fixed Idler Wheel are made of iron materials, are more firm, and not easily deformed. Besides, exceeding designated material specifications greatly increases this risk and will also damage the tool.
-
1700W Powerful Motor
The rebar bending machine features a 100% pure copper core high-power motor with double endurance for high conductivity, low noise operation, high-temperature resistance, and saves energy for a long time. Frequency: 60 Hz, Amps: 14A, Noise: 92 dB(A).
-
Humanized Foot Pedal & Handle
The foot switch connection to point 1,2 will make it more convenient to go to work. And when pressing the starting switch or the foot switch will bend the rebar to the angle you have set. When moving the bender by fixing the handle, 4 bolts can not loose, then move the bender together by 4 handles.
-
Extensive Application
The hydraulic rebar bender is widely applied in construction engineering / bridge construction / railway viaduct / dock highway bridges / electric power building. Perfect for bending rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc.
The rebar bender and cutter machine can bend 1/4''(#2) to 1"(#8) (6 to 25 mm) rebar to 0-180°in 6-7 seconds. Two standard foot pedal control switches for hands-free bending. This rod bending machine is multi-purpose for construction or all kinds of other things related to rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel bending. It is ideal for manufacturers who need simple, easy-to-use, consistent, and accurate steel bending machines. A must-have for the professional concrete installer!
- 6-7S Ultra-Fast Bending Speed
- 1700W Pure Copper Coil Motor
- Angle Adjustment Knobs
- Sturdy Machine Body
- Easy to Operate & Transport
Specifications
- Model: RB-25
- Voltage: 110V
- Power: 1700W
- Frequency: 60 Hz
- Amps: 14A
- Bending Angle: 0-180°
- Max. Rebar Diameter: 1" / 25 mm #8 Grade 60
- Min. Rebar Diameter: 1/4'' / 6 mm #2 Grade 60
- Bending Speed: 6-7 Seconds
- Bending Radius: 1.57'' / 40 mm
- Max. Rebar Hardness: HRC30
- Noise: 92 dB(A)
- Material: Iron
- Item Dimensions(L x W x H): 17.72'' x 19.69 x 20.08'' / 45 x 50 x 51 cm
- Packing Size(L x W x H): 19.69 x 22.05 x 22.05'' / 50 x 56 x 56 cm
- Net Weight: 200.62 lbs / 91 kg
- Gross Weight: 240.3 lbs / 109 kg
- Certificate: CE
- Application: Rebar, Round Steel, Flat Iron, Steel Bar Processing Plant, Construction Industry, Bridge Construction, etc
Package Content
- 1 x Electric Rebar Bender
- 2 x Foot Pedals
- 3 x Tension Springs
- 4 x Carbon Brushes
- 1 x User Manual
Please be aware that PO Box cannot receive items,please DO NOT fill in the PO Box address.
- DELIVERY DAYS: 3-7 BUSINESS DAYS
- 3 BUSINESS DAYS SHIPPING OUT
- SHIP FROM CA & TX & NJ & GA & NC &OR WAREHOUSE
California Warehouse: City of Industry, CA
Texas Warehouse: Houston, TX
New Jersey Warehouse: Perth Amboy, NJ
New York State Warehouse: Perth Amboy, NJ
Georgia Warehouse: Austell,GA
North Carolina Warehouse: Grove NC
Oregon Warehouse: AIRPORT WAY Portland,OR
- All of our items are backed with a 30-day return policy. We ensure all our items are new and in excellent condition prior to shipping. In case you receive the item that is not to the standards above, please contact us via e-Bay messages. All returns must be in new original condition as received and should be shipped with delivery confirmation
- Please note that all returns must be pre-approved by us. Unauthorized returns will not be accepted. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
- We ONLY accept returns with original package. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return.
- Email Customer Support:
- 9:00am-2:00am PST Sunday-Friday
- All emails will be responded to within 12-24 hours
- This item comes with 12 months Warranty from the date of customers purchased it. Special circumstances will be listed clearly in the listing.
- If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.
- Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's your fault.
- Replacement products are provided with the same warranty as the returned products.
Features & Details
- 6-7S Ultra-Fast Bending Speed: This electric rebar bender is designed with excellent performance. It helps save valuable person-hours by bending rebar 1/4'' #2 to 1" #8 Grade 60(6 to 25 mm) within 6 to 7 seconds. Bending Angle: 0-180°, Bending Radius: 1.57'' / 40 mm, Max. Rebar Hardness: HRC30, Item Dimensions(L x W x H): 17.72'' x 19.69 x 20.08'' / 45 x 50 x 51 cm.
- 1700W Pure Copper Coil Motor: This hydraulic bending machine features a 1700W pure copper motor, which can run quietly with low noise and significantly improve your working efficiency, reducing unnecessary wear. Besides, a copper motor can extend this electric rebar machine's operating life to a large extent. Voltage: 110V, Frequency: 60 Hz, Amps: 14A, Noise: 92 dB(A).
- Angle Adjustment Knobs: This rebar bending machine has two slide-type angle selectors, which can help you accurately bend any angle from 0-180 degrees. Preset angle locks are designed for repeating the same angle bending. When bending processing, the angle of point 1 must be bigger than point 2. Otherwise, the machine can not operate normally.
- Sturdy Machine Body: The electric bender machine adopts a sturdy iron machine body and durable Idler Wheel. Ø78 iron Gyre Idler Wheel and Ø94 Fixed Idler Wheel are stronger and not easy to break. Moreover, it can stand super-hard rebar with strong clamping force, which can help to reduce steel rebar waste.
- Easy to Operate & Transport: This hydraulic rebar bender comes with the standard foot pedal control switch for your easy hands-free bending. With four handles on the corner for you to transport and operate effortlessly. It is widely used in construction engineering for bending rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc.
- Note
- If your shipping address is in Canada, please provide the correct phone number and customer broker information.
- If your shipping address is in the United States, please provide correct phone number.
Key Features
-
6-7 Seconds Bending Speed
The steel rebar bender bends 1/4'' to 1" (6 to 25 mm) steel super fast in just 6 -7 seconds. Bending Angle: 0-180°. The bending speed depends on the thickness of the rebar and the angle you want to reach. Max. Rebar Diameter: 1" / 25 mm #8 Grade 60.
-
Two Angle Adjustors
Adjust the angle you need by moving left or right, and after angle adjustment is set accurately, ensure that the angle setting handle is fixed. When you find some abnormal during the operation, you must press down emergency stopped to close down the machine's operation.
-
Iron Idler Wheel
The high-strength Ø78 Gyre Idler Wheel and Ø94 Fixed Idler Wheel are made of iron materials, are more firm, and not easily deformed. Besides, exceeding designated material specifications greatly increases this risk and will also damage the tool.
-
1700W Powerful Motor
The rebar bending machine features a 100% pure copper core high-power motor with double endurance for high conductivity, low noise operation, high-temperature resistance, and saves energy for a long time. Frequency: 60 Hz, Amps: 14A, Noise: 92 dB(A).
-
Humanized Foot Pedal & Handle
The foot switch connection to point 1,2 will make it more convenient to go to work. And when pressing the starting switch or the foot switch will bend the rebar to the angle you have set. When moving the bender by fixing the handle, 4 bolts can not loose, then move the bender together by 4 handles.
-
Extensive Application
The hydraulic rebar bender is widely applied in construction engineering / bridge construction / railway viaduct / dock highway bridges / electric power building. Perfect for bending rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel, etc.
The rebar bender and cutter machine can bend 1/4''(#2) to 1"(#8) (6 to 25 mm) rebar to 0-180°in 6-7 seconds. Two standard foot pedal control switches for hands-free bending. This rod bending machine is multi-purpose for construction or all kinds of other things related to rebar, steel bar, steel rod, screw thread steel, carbon steel, round steel bending. It is ideal for manufacturers who need simple, easy-to-use, consistent, and accurate steel bending machines. A must-have for the professional concrete installer!
- 6-7S Ultra-Fast Bending Speed
- 1700W Pure Copper Coil Motor
- Angle Adjustment Knobs
- Sturdy Machine Body
- Easy to Operate & Transport
Specifications
- Model: RB-25
- Voltage: 110V
- Power: 1700W
- Frequency: 60 Hz
- Amps: 14A
- Bending Angle: 0-180°
- Max. Rebar Diameter: 1" / 25 mm #8 Grade 60
- Min. Rebar Diameter: 1/4'' / 6 mm #2 Grade 60
- Bending Speed: 6-7 Seconds
- Bending Radius: 1.57'' / 40 mm
- Max. Rebar Hardness: HRC30
- Noise: 92 dB(A)
- Material: Iron
- Item Dimensions(L x W x H): 17.72'' x 19.69 x 20.08'' / 45 x 50 x 51 cm
- Packing Size(L x W x H): 19.69 x 22.05 x 22.05'' / 50 x 56 x 56 cm
- Net Weight: 200.62 lbs / 91 kg
- Gross Weight: 240.3 lbs / 109 kg
- Certificate: CE
- Application: Rebar, Round Steel, Flat Iron, Steel Bar Processing Plant, Construction Industry, Bridge Construction, etc
Package Content
- 1 x Electric Rebar Bender
- 2 x Foot Pedals
- 3 x Tension Springs
- 4 x Carbon Brushes
- 1 x User Manual
SHIPPING
Please be aware that PO Box cannot receive items,please DO NOT fill in the PO Box address.
- DELIVERY DAYS: 3-7 BUSINESS DAYS
- 3 BUSINESS DAYS SHIPPING OUT
- SHIP FROM CA & TX & NJ & GA & NC &OR WAREHOUSE
California Warehouse: City of Industry, CA
Texas Warehouse: Houston, TX
New Jersey Warehouse: Perth Amboy, NJ
New York State Warehouse: Perth Amboy, NJ
Georgia Warehouse: Austell,GA
North Carolina Warehouse: Grove NC
Oregon Warehouse: AIRPORT WAY Portland,OR
PAYMENT
- We accept PayPal payment,PayPal Credit,Credit card or debit card and so on.
- Payment should be completed within 4 (Four) days of auction closing. Or unpaid dispute will be filed for closing auction.
- We will leave a positive feedback immediately after payment is received. We appreciate a positive feedback as much as you do. If for some reason there is any issue with the purchase, please contact us prior to leaving feedback, we will be glad to work together and provide a satisfying solution.
RETURNS
- All of our items are backed with a 30-day return policy. We ensure all our items are new and in excellent condition prior to shipping. In case you receive the item that is not to the standards above, please contact us via e-Bay messages. All returns must be in new original condition as received and should be shipped with delivery confirmation
- Please note that all returns must be pre-approved by us. Unauthorized returns will not be accepted. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.
- We ONLY accept returns with original package. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return.
CONTACT
- Email Customer Support:
- 9:00am-2:00am PST Sunday-Friday
- All emails will be responded to within 12-24 hours
WARRANTY
- This item comes with 12 months Warranty from the date of customers purchased it. Special circumstances will be listed clearly in the listing.
- If your item has been damaged in transit or become faulty in warranty period, please email us with pictures or video to show the problem.
- Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's your fault.
- Replacement products are provided with the same warranty as the returned products.