SHIPEED FROM US WAREHOUSE

RATTMMOTOR 1100W Permanent Magnet DC Brushless Servo Motor 200-6000RPM 3.55N.m+Servo Motor Speed Controller for Woodworking Machine/Lathe/Drilling and Tapping Machine/Reducer/Belt Sander (110V)     

servo motor driver

Feaures

  • Pure Copper Motor
  • Metal Gear
  • Strong power
  • Efficient heat dissipation
  • Infinitely adjustable speed
  • Self-locking switch
  • Dust shield
  • Multi-angle grinding
  • Wear-resistant and durable
  • Support one-key forward and reverse rotation, support soft start (both start and stop ease).
  • The motor output shaft has 15mm thread, which can be equipped with synchronous pulley and ER special chuck, which is widely used in belt sander, polishing machine, small lathe, milling machine, etc.
  • Pure copper motor, strong power and efficient heat dissipation.
  • Strong anti-interference ability, low noise, with multiple protections such as overcurrent, overload and overvoltage.

Parameters:

  • Power range: 1100w
  • Model: Brushless Servo Motor Control System
  • Rated torque (Nm): 3.55
  • Voltage range: 110V/220V
  • Motor pole pairs: 8 pairs
  • Input frequency: 50-60hz
  • Insulation class: F class
  • Speed range: 200-6000 rpm
  • Mounting size: 69mm
  • Mounting flange: 89mm
  • Outgoing shaft diameter: 15mm
  • Outgoing shaft length: 27+15mm
  • Motor length: 130mm
  • Mounting thread: M6 through-hole mm
  • Keyway: 5*5*20mm
  • Control method: turn on the power, adjust the speed with the knob
  • Protection mode: overcurrent, overvoltage, short circuit protection, locked rotor protection

Servo Motor Kit

Aluminum head

Adopting high quality aluminum head, not easy to crack under high intensity working condition.

Brushless Servo Motor Kit

All-copper motor & Thickened protective cover

  • High temperature resistance, good conductivity, long service life.
  • Strong power, 6000 rotational speed, can last more than 72 hours of work time.
  • Prevent sparks and dust from flying, and prevent the cutting piece from breaking and getting hurt.

woodworking machinery lathe drilling tapping

Cooling air outlet

360° grille air outlet design, strong heat dissipation, delayed service life.

Motor Speed controller

Purpose of each button:

  • F : Enter parameter combination key; combined with other keys to enter parameter setting mode, error recovery key
  • D: Direction switching; the main function is to switch directions and confirm parameter settings
  • + : Increase motor speed; adding keys to parameter and index values
  • - : Reduce motor speed; parameter and index value decrease key

Adjustment method for technician mode parameters:

  • a) Press and hold the "F" key while pressing the "+" key, and the screen will display as P-00;
  • b) Press the "+" or "-" keys to adjust the parameter number;
  • c) Press the "F" key to enter the parameters, and the screen will display the parameter values;
  • d) Press the "+" or "-" keys to adjust to the desired parameter value;
  • e) Press the "D" key to save the parameters and exit.

Restore factory settings:

  • While holding down the "F" key, press the "+" key once, and the screen will display as P-00. Then, hold down the "D" key for 3 seconds and release it.

Error code(Fault handling)

Er03: Motor Hall or phase line error

  • Poor plug contact;
  • The motor is not installed properly;
  • Hall is broken.

Er04: Locked rotor protection

  • Motor overload;
  • The four core wires connected to the motor and electronic control have poor contact.

Er05: Hardware overcurrent protection

  • Motor overload;
  • The signal line has poor contact or is broken.

Er07: Serial communication timeout error

  • The connection wire between the display screen and the motherboard is poor or the motherboard is damaged.

Technician mode parameter table:

P-02 Motor direction

  • 0: counterclockwise;
  • 1: Clockwise.

P-04 Starting speed

  • 200-800 rpm

P-05 Acceleration speed

  • 300-1350

P-07 Start switch

  • 0-1
  • 0: Knob start
  • 1: Key start

P-08 Brake function

  • 0-1
  • 0: Brake off
  • 1: Brake activated

P-10 Automatic running in

  • 0: Ordinary sewing;
  • 1: Automatic running in.
  • Turn off the power and stop
  • Stop running in

P-12 Acceleration time

  • 4-120
  • Acceleration time

P-14 Maximum current limit

  • 50-500

drilling machine

Applications

Suitable for: belt sander, small lathe, woodworking machinery, CNC precision carving, medical equipment, drilling, milling and tapping power head, sewing machine equipment, spray painting equipment, packaging equipment, laser equipment, CNC machine tools, 3C industry equipment, assembly line transmission and robot power. 



SHIPPING ADDRESS
  • Items will be shipped from the US warehouse, items will be dispatched within 1 working day, valid logistics tracking number will be dispatched within 3 working days.
ABOUT THE PRODUCT MANUAL
  • If you have not received the product manual and related information, please contact us. 
AFTER-SALE