52CC 2.3HP Gas Powered T-Post Driver Fence Farm Push Pile,Gasoline Engine Pile Driver Jack Hammer 55mm 70mm
Feature:
★ Easy Recoil Starter.
★ Comes With 2 Post Driving Head (55mm/70mm) Makes This a Perfect Choice For T-Posts, Y-Posts And Ground Rods.
★ Vibration Absorbing Springs For Stable Operation.
★ Superior Cooling Vents For Prolonged Use And Smooth Running.
★ Interlocking Controls With Throttle Adjuster.
★ Heavy-Duty Aluminium Driver Casing.
★ Rubber And Plastic Sponge Handle Which Can Greatly Reduce The Recoil Force Of The Machine.
★ Lightest Weight, Simple One Man Operation, Lowest Displacement.
★ Easy To Use.
★ Durable in use. This Gasoline Post Driver provides maneuverability and usability of being able to drive almost anything.
Detail:
Engine Type: Two-Stroke, Air Cooling, Single Cylinder
Displacement: 52cc
Fuel Type: Mixed Oil (25 Gasoline: 1 Motor Oil)
Fuel Tank Capacity: 1 L
Max. Power & Speed: 1900W(2.3HP)/6500r/min
Max. Torque & Speed: 2.5N.m/5500r/min
Fuel Consumption Rate: ≤0.5L/h
Arial Frequency: 800-2800BPM
Arial Energy: 25-45J
Carburetor Type: MZ15-048
Spark Plug Type: BM6A
Starter System: Hand Pull Start
Size: Approx. 74*34*26cm
Post Driving Head Mount Size: (55mm,70mm)
Package Included:
1x Petrol Post Driver
2x Post Driving Head
1x Mixing Oil Bottle
1x Tools Kit
Tips:
1. If the pile driver has the problem of not hammering:
1) . Whether too much butter is added at the place where the butter is added, clean up the excess oil in the cylinder before disassembling and re-add about 20g of high temperature resistant butter.
2) . The speed of the carburetor can be slightly fine-tuned. If the Arial frequency is too high, it can be lowered if the hand cannot hold it. Otherwise, the Arial frequency should be increased. Note that it is fine-tuning.
2. The machine is not easy to start.
First, check the ratio of oil: gasoline: oil = 25:1, be sure to use a good second-flush oil. The starter rope is pulled out an arm's distance, and it can be started by pulling it two or three times in a row, but it is also related to the temperature, and sometimes it needs to be pulled several times. When the cold engine starts, close the damper (for good start, the warm engine can be opened and start) and open the damper after the machine is normal.
1. Whether too much butter is added at the place where the butter is added, clean up the excess oil in the cylinder before disassembling and re-add about 20g of high temperature resistant butter.
2. The speed of the carburetor can be slightly fine-tuned. If the Arial frequency is too high, it can be lowered if the hand cannot hold it. Otherwise, the Arial frequency should be increased. Note that it is fine-tuning.
2. The machine is not easy to start. First, check the ratio of oil: gasoline: oil = 25:1, be sure to use a good second-flush oil. The starter rope is pulled out an arm's distance, and it can be started by pulling it two or three times in a row, but it is also related to the temperature, and sometimes it needs to be pulled several times. When the cold engine starts, close the damper (for good start, the warm engine can be opened and start) and open the damper after the machine is normal.
Dear Customer，
Thank you very much for your orders. I'mpleased that you entrusted us as your supplier foryour project and am grateful that you continue toput your faith in our services. I hope our productsmet your expectations.
As always, we are happy to support you with anyfuture projects you may undertake. I wish you thebest with your current project and look forward toseeing the outcome. Thank you again, and I lookforward to working with you in the future .
Best regards.
- We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
