Features:

1. Realize high-frequency, fast, frequent on and off of the circuit, Sukima Switch for times;

2. The on and off process will not generate noise, sparks, or electromagnetic ;

3. The service life is longer than that of common electromagnetic relays;

4. Adopt dual MOS parallel active output, lower internal resistance, larger current, strong power, 10A and 400W at room temperature, which meets the needs of most equipment;

5. Commonly used to control motors, bulbs, LED light strips, DC motors, pumps, solenoid valves, etc. These devices can be easily controlled through this module, which is very convenient.

Module highlights:

1. Wide voltage operation (5-36V), most devices can be used, very convenient;

2. Clear and concise interface, powerful functions, easy to understand, almost meet all your needs;

3. 1-button stop function (STOP button) with reverse connection protection, reverse connection will not burn;

4. Add sleep mode, automatically turn off the display without any operation within 5 minutes after turning it on;

for Wake up by any button;

5. Different OP, CL, LOP parameters can be set, these parameters are independent of each other and saved separately;

6. All set parameters are automatically saved when power is off.

Working mode:

P1 mode: After the signal is triggered, the relay conducts for OP for time and then disconnects; during the OP for time, the following operations are performed

P1.1: The signal is invalid if it is triggered again

P1.2: The signal is triggered again and the timing is restarted

P1.3: The signal is reset if it is triggered again, the relay is disconnected, and the timing stops;

P-2: Give a trigger signal, the relay disconnects for CL for time, and then the relay conducts for OP for time. After the timing is completed, the relay is disconnected;

P3.1: Give a trigger signal, the relay is energized for OP for time, and then the relay is disconnected for CL for time, and then the above actions are repeated. If a signal is given again during the cycle, the relay is disconnected and the timing stops; the number of cycles (LOP) can be set;

P3.2: After power is on, no trigger signal is required. The relay conducts for OP for time and the relay is disconnected for CL for time. Cycle the above actions; the number of cycles (LOP) can be set;

P-4: Signal hold function: If there is a trigger signal, the timing is reset and the relay remains on; when the signal disappears, the timing is OP and the relay is disconnected; during the timing, if the signal is input again, the timing is reset to for zero;

Specifications:

Part name: DC 5V-30V Dual MOS for Time Delay Relay

Material: abs

Color: white

Size: as shown in the figure

1: Working voltage: DC 5V -36V;

2: Trigger signal source: high level trigger (DC 3.0V-24V) The signal ground and the system ground are not shared, which improves the system's anti- ability (it can also be short-circuited to share the ground)

3: Output capacity: DC 5V-36V, continuous current 15A at room temperature, power 400W! Under auxiliary heat dissipation conditions, the maximum current can reach 30A.

4: Static current: 15mA

5: Service life: unlimited switching for times; Operating temperature: -40-85℃; Size: 6.0*3.4*1.2cm

6: Equipped with optocoupler isolation, enhanced anti- ability, industrial-grade circuit board, and permanent memory of set parameters after power failure.

Relay enable mode:

1. ON: Allow the relay to conduct during the OP conduction for time;

2. OFF: The relay is prohibited from conducting and is always in a closed state;

Short press the STOP key on the main screen to switch between ON and OFF, the current state will flash, and then return to the main screen. (This function is an stop function, and the relay can be turned on and off with 1 button)

Sleep mode:

1. CP sleep mode: No operation within five minutes, the digital tube automatically turns off the display, and the program runs normally;

2. Od normal mode: The digital tube is always displayed; 

Long for press the STOP key for 2 seconds, then release it to switch between CP and Od states. The current status will flash and then return to the home screen.

Package Contents:

1 * Control Panel

Note:

1: Please allow 1-2 cm error due to manual measurement, please make sure you do not mind before ordering.

2: Due to the difference between different monitors, the image may not reflect the actual color of the item

Payment must be completed within 5 days. If you have any problems about payment, please contact us via message.

We only ship to confirmed Order addresses. Please comfirm that your Order for ADDRESS is in line with your shipping for ADDRESS.

Please kindly note that the combined shipping is not provided because the shipping fee is calculated by weight. Also, the each additional item means exactly the the same color and size. 

It takes about 7-15 working days to US; about 10-30 working days to other countries.  for TRANSIT time may be a little delayed because of the bad weather and customs inspection. If you do not receive your item within 30 working days since payment finished, please contact us immediately for further assistance.

We strive for 100% customer satisfaction! Positive is very important to us. If you have any questions, please feel to contact us via "Ask seller a question" . We will reply your email within 24 working hours.