Bond It Self Levelling Compound Levelmaster Floor Cement Screed Concrete 10/20kg

Description:
A one part, cementitious, chloride/protein‐free, levelling compound. When mixed with water it provides a
smooth, level base for most common internal floor types such as concrete and sand/cement screed.
Conforms to EN 13813 CT‐C16‐F4.

Benefits:
u Self‐smoothing.
u Accepts foot traffic after 3‐4 hours depending on
temperature and humidity.
u Preblended, requiring only the addition of water.
u Single pack and easy to use.
u Can be applied up 6mm thickness.

Uses
LevelMaster STANDARD is an ideal underlay for levelling most
common internal subfloors prior to the installation of floor
coverings. Note: Not suitable for use with under floor heating
installations or areas subject to limited movement / vibration,
unless used in conjunction with LevelMaster LATEX
LIQUID. Alternatively, LevelMaster AD-FLOOR or
LevelMaster AD-FLOOR PLUS should be used. This
product is not designed as a final wearing course
to receive traffic and must be covered with either
tiles, lino, vinyl, carpet, etc.

Preparation
Surfaces must be clean, dry, structurally sound and free from
grease, oil, paint, polish or any other contaminate that may hinder
adhesion. Porous surfaces should be dampened down (without
pooling or standing water). Very absorbent surfaces should be
primed with a waterproof primer such as Bond It PRIMER &
FLEXIBLE ADMIX or SBR. Wooden floors should be overboarded
with 15mm exterior grade plywood rigidly fixed with screws at
300mm centres. The plywood should be primed as for very porous
surfaces.Anhydrite/calcium sulphate
screeds should be sanded and vacuumed
before priming with 2 coats of Bond It
PRIMER AND FLEXIBLE ADMIXTURE and
left to dry for 24 hours prior to
application. Note: PVA is not suitable for
priming surfaces prior to application of
LevelMaster STANDARD.

Mixing
Use 3.6L of clean water for every 20Kg bag of LevelMaster
STANDARD. Slowly add the powder to the water while stirring
with a suitable slow speed drill or paddle. When using LATEX
LIQUID refer to dosage on bottle.

Application
Pour the mix onto the subfloor within 10 minutes of mixing to a
maximum thickness of 6mm. Use a flooring trowel or float to
promote a smooth surface. This product can be built up to 10 -
12mm in thin layers, ensuring that the previous layer has fully
hardened / cured. Allow adequate ventilation during curing.
LevelMaster STANDARD will accept light foot traffic after 4 hours;
however, floor coverings should not be laid for 24 hours (longer
when used in conjunction with LATEX LIQUID).

Cleaning
All tools and equipment should be cleaned in water. Cured
material can only be removed by mechanical means.

Limitations
Do not use at temperatures below 5o
C or above 30oC. High
temperatures will reduce the open time. Cold or humid conditions
will slow the drying times. LevelMaster STANDARD does not
provide a final wearing surface and must be covered with a
floorcovering (ceramic tiles, wood flooring or carpet). Not suitable
for use in conjunction with underfloor heating systems. Do not
mix more material than can be used in 10 minutes.

Coverage
Depends upon the condition of the subfloor surface, however, a
10Kg bag will cover approximately 3.6m2 at a depth of 3mm.

Storage Conditions
This product must be stored in unopened manufacturers bags
away from extremes of temperature and in dry conditions. This
product must be used within 12 months of manufacture and
before the use by date shown on this bag.

Disposal of Containers
Do not leave empty containers where residue could be harmful to
children, animals or the environment. Remove any containers to a
central disposal point in accordance with local regulations.

Health & Safety
Please refer to separate material safety data sheet for full handling, use and storage
instructions. Keep out of reach of children. It is the users responsibility to determine suitability
for use. If in doubt contact our Technical Department for advice.
Note: this information is for general guidance only, since site conditions and labour are beyond our
control. It is recommended that users make their own tests to determine suitability

Specification Summary
Flammability Non-flammable
Appearance Grey granular powder
Setting Time Foot traffic in 4 hours
Wet Density 2g/ml
UFI GN20-K02W-A000-WSEC

Product Details:
Colour: Grey
Colour: BDH100B BDH102B
Size: 10 Kg 20 Kg
Barcode: 5060021361318 5060021363282

Package Content:
1x Bond It Self Levelling Compound Levelmaster Floor Cement Screed Concrete Bar