SHIPEED FROM CHINA
RATTMMOTOR 800W Water Cooled Spindle Kit, 65mm Spindle Motor 0.8KW 220V 400HZ+1.5KW VFD 220V Single to 3 Phase Inverter Variable Frequency Drive+65mm Spindle Mount+ER11 Collet+80W Water Pump for CNC
Package Include ( What you see is what you receive )
- 1 x 0.8KW Water Cooled Spindle Motor ER11
- 1 x 1.5KW VFD 220V
- 1 x 65mm Spindle Motor Mount
- 1 x 80W Water Pump 220V
- 1 x 5m Pipe
- 14 x ER11 Collet（1mm, 1.5mm, 2mm, 2.5mm, 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 3.175mm）
Water Cooled Spindle Motor
- Power: 800W
- Voltage: 220V AC
- Speed: 24000RPM
- Szie: 65x158mm
- Frequency: 0-400Hz
- Collet Size: ER11
- Material: Stainless Steel
- Accuracy: 0.003--0.005
- Runout off: Less than 0.01mm
Variable Frequency Drive
- Power: 1.5KW
- Input Voltage: 220V(+/-15%)
- Output Voltage: 220VAC
- Input Frequency: 50-60 Hz
- Output Frequency: 0-1000 Hz
- Input Phase: 1 phase
- Output Phase: 3 phase
65mm Spindle Motor Mount
- Made of high quality cast aluminum, this spindle motor mount is strong and durable.
- The surface is well finished by sand blast which ensures a better smoothness.
- This bracket would be a great replacement for CNC parts.
Water Pump
- Power: 80W
- Voltage: 220V AC
- Flow Rate: 3500L/H
- Lift Height: 3.5M
- Overall Dimension:153x88x108mm
5M Water Pump
With 5M water pump for 0.8KW spindle motor kit.
14pcs ER11 Collet
- Size:1mm, 1.5mm, 2mm, 2.5mm, 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 3.175mm(1/8").
- First class 1065 carbon steel
- Hardened and precision ground
- Made of high grade specially formulated spring steel
Applicable Engraving Materials
The Spindle motor is mainly suitable for NON-metallic engraving.For example: wood, plastic, acrylic, pvc, pcb, carbon fiber, density board and soft metal like copper, aluminum and the similar materials.
RATTMMOTOR CNC Spindle
High Quality Bearings
Using optimized bearings, this series of bearings has strong hardness and rust resistance, as well as dynamic balancing technology, the actual runout off of the spindle is close to 0.01 mm, the precision tapered bore is less than 0.005mm, high precision and durable.
Connect Spindle Motor to VFD
The wiring method of the spindle motor and the inverter is as follows:
- VFD's U= Spindle's U1
- VFD's V= Spindle's V1
- VFD's W= Spindle's W1
- Connect any 2pin terminal "R", "S" or "T" of the inverter to "110VAC".
Fuction keys description
- RUN key: Run command
- FOR/REV: Change the running director of motor
- ( DISP ) Shift key: Status monitor mode switch, parameter of third stage menu switch
- SPEED: Speed controller
- ESC: Return to the starus of "ENTER"
- ( ENTER ) SET Key: Enter into menu, enter into parameter or parameter date writing confirm
- ( UP ) Value change key: Parameter of fuction code, data increase, revise and select all kinds of modes
- ( DOWN ) Value change key: Parameter of fuction code, data decrease, revise and select all kinds of modes
- STOP/RESET key: Stop command / abnormal command
- LED display zone: Indicating for RUN, frequency, current, voltage, reverse
Description of control terminals / Description of jumper fuction:
Inverter wiring involves main circuit and control circuit. The user can raise the cover of housing, at this time main circuit terminal and control circuit shall be viewed, and the user conduct correct connection as per wiring circuit below.
- X1, Set as forward during delivery
- X2, Set as reverseduring delivery
- X3, Set as reset during delivery
- X4, Set as high speed during delivery
- X5, Set as medium speed during delivery
- X6, Set as low speed during delivery
- GND, Digital/analog/communication and power earthing terminals, lsolation of GND inside from PE
- P12, +12V power supply, Maximum output current 150mA
- A11, Analog voltage input, Input voltage range:0-+10V
- J1: Selection of X1-X6 wiring mode: NPN PNP ( Ex-factory setting: PNP)
- J2: Selection of AO output: VO, voltage AO, current ( Ex-factory setting: VO)
- J3: Selection of AI2 input: V, voltage A, current ( Ex-factory setting: A)
- J4: RS485 communication interface terminator enabled: ON OFF ( Ex-factory setting: OFF)
- J5: Selection of X6 terminal fuction reuse: X6 Y1-PEO ( Ex-factory setting: X6)
Specification of Protection Control:
- Overload protection: Electric relay protection motor driver
- Fuse protection: In case of fuse, the motor stops running
- Over voltage / Low voltage
- Restart after transient stop: Restart after transient stop through frequency tracking mode
- Stall prevention: Stall prevention during acceleration/deceleration
- Short circuit of output terminal: Electronic protection
- Overheating protection of ridiating fin
- Other fuctions: reverse limit, direct startup after operating, fault reset, parameter locking, ect.
Description of main circuit terminals:
- L / N: Input power terminal, connected to singe-phase power
- U / V / W: Input output terminal, connected to three-phase motor
- DC+ / DC- : DC output + terminal, DC bus output terminal is used for connecting external brake unit or common DC bus system.
- DB: Brake output terminal, connecting brake resistor between DB and DC+
- PE: Earthing terminal, inverter housing earthing terminal must be earthed.
RATTMMOTOR 1.5KW 220V VFD
- Frequency range: 0-1000Hz
- Accuracy: 1) Digital type: 0.01％(-10～40℃); 2) Analog type: 0.1％(25±10℃)
- Setting resolution: 1) Digital type: 0.01Hz; 2) Analog type: 1％ of the maximum operating frequency
- Output resolution: 0.01Hz
- Keyboard setting mode: Set directly
- Analog setting mode: External voltage 0-5V, 0-10V, 4-20mA, 0-20mA
- Other Ductions: 3 hopping frequencires (lower-frequency limit, start-up frequency and stop frequency) can be set respectively.
- Control Mode: V/F Vector Control
- Communication Control: RS-485
- Vibration: Below 0.5G