Door Topographic Map Overlays - *2025+ 4Runner

Easy to apply Adds subtle styling For front AND rear doors *NOTE: Designed for NON-TRD vehicles, but can be modified. See install video below 2025 4Runner Topographic Map Door Overlays These vinyls really do add some style to the interior of your 2025 Toyota 4Runner. The contour lines are printed on clear vinyl and then topped with a layer of matte laminate to protect it all. Your original door color fills in the blank spots and the overall finished product looks great. Works with all color interiors. Comes with 1 extra set. *NOTE: Designed for NON-TRD vehicles, but can be modified. See install video below. Photos on the blue trim TRD Sport Tacoma are just for reference. This does not change the color of the original trim. It only adds lines. Instructions Clean the application area to prepare it for installation. Just use a wax free detailing spray. Get the inside of the cabin to about 72-75 degrees.NOTES: We recommend that the installation area be free of Armor All and not in direct sunlight. Microfiber Detailing Spray Soapy Water (we recommend our StickerFab Installation Fluid) Heat Gun or Hair Dryer (optional) Felt Tip Squeegee Wet installs require one drop of dish or hand soap in a cup of water, however we prefer and highly recommend using StickerFab Application Fluid. Apply to the vinyl and the surface of your trim so that the vinyl doesn't stick to anything it touches immediately. Then you can slide it around until you find the correct position. You can also remove it while both surfaces are wet. Once happy with the alignment, push out the extra water with your fingers and squeegee. Be gentle when using your fingers and a squeegee especially if the vinyl gets warm. Gradually apply more pressure as you get it aligned. Do not allow water bubbles to form. Work slowly until they are all gone. Allow to dry in the sun and then come back one final time to make sure all the edges are down. You can use light heat from a heatgun or hairdryer on the edges as well. Make sure the heat isn't high enough to burn yourself. If it's too much for you to handle, it will likely be too much for the vinyl. Try doing the install in the shade so it doesn't heat up the vinyl rapidly. Exposure to sun at the end though is encouraged.

Door Topographic Map Overlays - *2025+ 4Runner

Easy to apply
Adds subtle styling
For front AND rear doors
*NOTE: Designed for NON-TRD vehicles, but can be modified. See install video below

2025 4Runner Topographic Map Door Overlays

These vinyls really do add some style to the interior of your 2025 Toyota 4Runner. The contour lines are printed on clear vinyl and then topped with a layer of matte laminate to protect it all.

Your original door color fills in the blank spots and the overall finished product looks great. Works with all color interiors.

Comes with 1 extra set.

*NOTE: Designed for NON-TRD vehicles, but can be modified. See install video below. Photos on the blue trim TRD Sport Tacoma are just for reference. This does not change the color of the original trim. It only adds lines.

Instructions

Clean the application area to prepare it for installation. Just use a wax free detailing spray. Get the inside of the cabin to about 72-75 degrees.

NOTES: We recommend that the installation area be free of Armor All and not in direct sunlight.

Microfiber
Detailing Spray
Soapy Water (we recommend our StickerFab Installation Fluid)
Heat Gun or Hair Dryer (optional)
Felt Tip Squeegee

Wet installs require one drop of dish or hand soap in a cup of water, however we prefer and highly recommend using StickerFab Application Fluid. Apply to the vinyl and the surface of your trim so that the vinyl doesn't stick to anything it touches immediately.

Then you can slide it around until you find the correct position. You can also remove it while both surfaces are wet. Once happy with the alignment, push out the extra water with your fingers and squeegee. Be gentle when using your fingers and a squeegee especially if the vinyl gets warm. Gradually apply more pressure as you get it aligned.

Do not allow water bubbles to form. Work slowly until they are all gone. Allow to dry in the sun and then come back one final time to make sure all the edges are down. You can use light heat from a heatgun or hairdryer on the edges as well. Make sure the heat isn't high enough to burn yourself. If it's too much for you to handle, it will likely be too much for the vinyl.

Try doing the install in the shade so it doesn't heat up the vinyl rapidly. Exposure to sun at the end though is encouraged.