SH01
【Remove Excess Moisture】3D printer filaments are hygroscopic, moisture would cause printing failure. Sovol SH01, a great addition to 3d printer, can remove excess moisture, keep your filament dry and bring you better prints. The surface of prints will be smoother, the layer adhesion increased. No more brittle PLA, PETG, ABS filament
【Real-time Monitoring of Temp and Humidity inside】Displays the humidity and temperature in the dry box in real time. Setting temperature 40 °, 45 °, 50 ° C and setting time from 6 hours to 12 hours. If you use SH01 in a room with room temperature under 16℃, the temperature in the dryer box would not come up to 50℃. But do not worry, this would not decrease drying effect
【Excellent Power-off Drying Mode】Silicone & PTFE seal makes it possible to store filaments for a long time without power and protects your filaments from moisture and dirt. You can put 4 bags of desiccants (not included in the package) inside the dryer box to improve drying efficience & quality
【Large Capacity】 Sovol dryer box can store 2 filament rolls with a width of less than 70 mm or 1 filament roll with a width of less than 150 mm. Please open the PTFE seals on the top of the box during heating for Moisture evaporation
【Heating More Evenly】 The unique design of the built-in fan in the box is based on the principle of modynamics of air, makes the filament heated more evenly. SH01 makes drying more efficient. Any questions about the product please feel free to let us know. Our technical support team will provide service as soon as we can
【You Must Know...】 Place the filament into the filament outlet. Please note that the direction is placed counterclockwise so that the pulley at the bottom can feed better.If the screen displays two errors, E0 and E1, please open the drying box and check all the cable sockets on the motherboard to see if they are damaged or loose. If there is any problem, please feel free to let us know. We will send replacement for you
SH02
【Dual Spool Filament Dryer Box】- Each Sovol SH02 filament dryer is equipped with 2 filament holes which allow PTFE pipes through. The newly designed filament hole position is convenient for 3D printers with different extruder positions on the market. Large capacity of drying 2 rolls of 1KG filament at the same time meets the needs of users to dry a wide range of filaments and two printers at the same time, saving space and making the work area tidier.
【150W PTC Fast Heater】- Different from Sovol SH01, SH02 comes with 150W PTC heater which can heat up faster and are more energy-efficient. SH02 dryer box can reach 50°C within 7 mins and reach 70°C within 25 mins. Also you can set 40-70°C as you wish. The dryer quickly heats with a built-in fan, circulating hot air 360° for uniform heating, effectively drying moisture filaments and improving your 3D printing results.
【Better Sealing than SH01】- We changed the sealing design of SH02 filament storage box and used thicker sealing materials with stronger sealing performance. Even when it is not powered on, SH02 protects your filaments from moisture and dirt. You can put 4 bags of desiccants (not included in the package) inside the dry box to improve drying efficience & quality.
【One Key Set for Each Type of Filaments】- Sovol SH02 has one-key temperature setting for 9 different types of 3D Printing filaments, including PLA, TPU, PETG, ABS, ASA, PVA, PC, PA, PP. We have set default drying temperature and time for each type of filaments in advance. Just press one key to choose the filament type and the drying box will start working as you expected immediately.
【Smart Safety Protection】- When PTC temperature exceeds 130°C, it will automatically cut off the heating, and when the PTC temperature drops below 90°C, it will automatically resume heating. If the fan stops rotating during use, an alarm will sound to prompt you to replace the fan to prevent the PTC module from burning out.
SH03
Dual Independent Heating Chambers: Sovol SH03 dry box comes with 2 chambers controlled independently. You can only use one of them or make both 2 chambers working at the same time to heat up to different temperature for different type of filaments. Since SH03 can be sealed to store dried filaments without power, you can also make one chamber drying while another one for storage without power
200W+200W PTC Fast Heater: Sovol SH03 equips with dual 200W PTC heater which can heat up to 85°C max temp faster and are more energy-efficient. SH03 dryer box can reach 50°C within 4 mins and reach 70°C within 12 mins. The dryer quickly heats with a built-in fan, circulating hot air 360° for uniform heating, effectively drying moisture filaments and improving your 3D printing results
No More Moisture in the Chamber: When SH03 is working and the temperature inside the chamber reaches the preset target temperature, the moisture vent will open. Auto Dehumidification System helps moisture in the chamber quickly discharged and resolves the pain points of most filament drying boxes on the market for users
4 Spools Filament Dryer Box: Each Sovol SH03 filament dryer is equipped with 4 filament holes which allow PTFE pipes through. The newly designed filament hole position is convenient for 3D printers with different extruder positions on the market. Large capacity of drying 4 spools of 1KG filament at the same time meets the needs of users to print with multicolor and use 4 printers at the same time, saving space and making the work area tidier
One Key Set for Each Type of Filaments: Sovol SH03 has one-key temperature setting for 10 different types of 3D Printing filaments, including PLA, TPU, PETG, ABS, ASA, PVA, PET, PC, PA, PP. We have set default drying temperature and time for each type of filaments in advance. Just press one key to choose the filament type and the drying box will start working as you expected immediately.
