Radtel RT-910 CB TRANSMIT VERSION Air Band VHF UHF AM FM CB.2 ANTENNAS Scanner

Bluetooth Programming

Easily program your radio wirelessly via Bluetooth — no cables required.

• Compatible with iOS & Android devices

• Use the official Radtel app to configure frequencies, channels, power settings, and more

• Fast and flexible for both beginners and advanced users

---

🔹 Noise Reduction (DSP Technology)

Enhanced digital noise suppression ensures clear communication even in loud environments.

• Filters out background noise in real time

• Ideal for construction sites, events, industrial, or outdoor use

• Improves voice clarity and reduces fatigue in long-term usage

SQL (Squelch) – Noise Filter Control

Squelch determines whether the radio stays silent or emits static when no valid signal is detected.

• Level 0: Squelch OFF – all background noise passes through

• Higher Levels: Block weak or unwanted signals

• Recommended: Mid-range setting for optimal balance between reception and noise suppression

---

STEP (Frequency Step)

Defines the step size when tuning frequencies in VFO mode or scanning.

• Available Values: 2.5K / 5.0K / 6.25K / 10.0K / 12.5K / 20.0K / 25.0K / 50.0K

• Tip: Match with your region’s standard frequency spacing

---

TXP (Transmit Power)

Select the desired transmission power level:

• HIGH: Maximum range, faster battery drain

• MIDDLE: Balanced between power and efficiency

• LOW: Energy-saving, shorter range

---

SAVE (Power Save Mode)

Reduces battery consumption during standby by controlling the radio's sleep/awake ratio.

• OFF: Power-saving disabled

• 1: Normal Mode

• 2: Super Mode

• 3: Deep Power Save Mode

  VOX (Voice Operated Transmit)

  Allows hands-free operation by transmitting when sound is detected (no PTT button needed).

• OFF: VOX disabled

• Levels 1–9: Enable VOX, with Level 1 being the most sensitive

• ⚠️ Higher sensitivity may trigger transmission in noisy environments

• ---

   

  📶 W/N (Wide/Narrow Bandwidth)

  Select the transmission bandwidth:

• WIDE (25 kHz): Better audio quality

• NARROW (12.5 kHz): Saves spectrum, ideal for crowded or regulated areas

• ---

   

  💡 Backlight (ON / Auto OFF)

  Controls display lighting:

• ON: Always-on backlight

• OFF: Backlight turns off after inactivity to save battery

• ---

   

  🔄 TDR (Dual Standby)

  Monitor two channels/frequencies alternately.

• ON: Dual standby enabled

• OFF: Single-channel monitoring only

• ---

   

  🔔 Beep (Keypad Tone)

  Enables audible feedback when pressing buttons.

• ON: Key tones active

• OFF: Silent keypad operation

• ---

   

  ⏱ TOT (Time-Out Timer)

  Limits transmission duration to avoid long accidental transmissions.

• OFF: No limit

• ON: Transmission is limited to preset time

• ---

   

  📁 Channel Add (CH Memory Programming)

  Save VFO frequencies to channel memory (CH0–CH256).

• Channels marked “CH-” are already programmed

• ---

   

  🗑 Channel Delete

  Delete saved channels from memory.

• Empty channels (no “CH”) cannot be deleted

• ---

   

  🔒 CTCSS (RX/TX – Analog Sub-Tone)

• RX CTCSS: Radio unmutes only if incoming signal has matching tone

• TX CTCSS: Transmits selected tone with voice

• OFF: No tone used

• Supports standard & custom tones

• ---

   

  💻 DCS (RX/TX – Digital Code Squelch)

• RX DCS: Only receives signals with matching DCS code

• TX DCS: Transmits selected DCS code

• OFF: Disabled

• Choose from standard presets or enter custom codes

• ---

   

  🔐 VOICEPRI (Voice Privacy / Subtone Encryption)

  Encrypts your audio signal using sub-tone scrambling.

• OFF: No encryption

• Levels 1 / 2 / 3: Increasing levels of privacy

• Prevents unauthorized listening on same frequency

• ---

   

  📝 CH-NAME (Channel Naming)

  Assign custom names to saved channels.

• Use # key to switch input modes (letters/numbers/symbols)

• ---

   

  ✅ ROGER (End-of-Transmission Tone)

  Plays a tone at the end of each transmission.

• OFF: No tone

• BEEP: Standard confirmation tone

• TONE1200: Playful “frog” tone

• ---

   

  🗣 VOICE (Voice Prompts)

  Audible feedback for settings and button presses.

• ON: Prompts enabled

• OFF: Prompts disabled

• ---

   

  🌐 LANGUAGE (Voice Prompt Language)

  Choose the voice prompt language:

• ENGLISH

• CHINESE

• ---

   

  🚫 BCL (Busy Channel Lockout)

  Prevents transmitting if the channel is already in use.

• ON: Blocks transmission on busy channel

• ---

   

  🔍 SC-REV (Scan Resume Mode)

  Sets scan behavior when a signal is detected:

• TO (Time Operation): Resume scan after 5 seconds

• CO (Carrier Operation): Resume only after signal ends

• SE (Search Operation): Stop scan and stay on signal

• ---

   

  🎛 PF2 / PF3 (Programmable Function Keys)

  Assign custom features to short or long presses:

• Options: SOS, LAMP (Flashlight), RADIO (FM), TXPOWER, SCAN, SEARCH, NOAA

• PF2 and PF3 can be independently customized

• ---

   

  🔄 OFFSET (TX/RX Frequency Offset)

  Defines the frequency difference used with repeaters.

• Example: 0.6000 MHz for VHF

• Used with SFT-D to calculate final TX frequency

• ---

   

  ➕➖ SFT-D (Shift Direction)

  Sets direction for frequency shift:

• OFF: Simplex operation

• +: TX = RX + offset

• –: TX = RX – offset

• ---

   

  ⚡ POWER ON MSG

  Choose what’s displayed when powering on the device:

• LOGO: Shows Radtel or custom brand logo

• VOLTAGE: Displays current battery voltage

• OFF: Allows transmission regardless

• High-concerned chemical

  None
  Use

  others
• Output Power(w)

  3w-5w
  Battery Capacity(mAh)

  1500mAh
• Waterproof / Water-Resistant

  No
  Battery Included

  Yes
• Material

  Plastic
  Storage Channel

  960
• Frequency Range

  108-136mhz,65-108mhz
  Dimensions

  13cm*6cm*5cm
• Model Number

  RT-910B
  Walkie Talkie Type

  Portable
• Is_Display

  Yes
  Maximum Range

  3km-5km
• Brand Name

  radtel
  Origin

  Mainland China