If your vehicle requires 2" spacers but you purchased ≤1" , the stock studs are longer than the adapters, and the wheels do not have hollow spot in them, you may need to grind, or cut your existing lugs if you don't choose to purchase shorter studs.
(2) 2 Inch 4x110 ATV Wheel Spacers 10x1.25 For 2008-2012 Bombardier DS450
Specification:Quantity : 2PCS | For 2 Wheel
Hubcentric : No
Thickness : 2 inches or 2'' or 50.8mm
Bolt Pattern : 4x110 or 4/110
Center bore :84mm
Thread/Nuts: 10mm x 1.25 or 10x1.25 or M10x1.25
Hubcentric : No
Thickness : 2 inches or 2'' or 50.8mm
Bolt Pattern : 4x110 or 4/110
Center bore :84mm
Thread/Nuts: 10mm x 1.25 or 10x1.25 or M10x1.25
Fitment:
For Honda |
1997-2009 Recon 250 |
1988-2000 FourTrax 300 |
1986-1987 FourTrax 350 |
1987-1989 FourTrax Foreman 350 |
2000-2009 Rancher 350 |
2004-2009 Rancher 400 (4WD) |
1996-2006 Foreman 400 (4WD) |
2004-2016 Rancher 420 (4WD) |
1998-2004 Foreman 450 (4WD) |
2005-2016 Foreman 500 (4WD) |
2001-2016 Foreman Rubicon 500 (4WD) |
2003-2007 Rincon 650 |
2006-2016 Rincon 680 |
For Yamaha |
1995-1998 Timberwolf 250 |
1999-2005 Bear Tracker 250 |
2006-2009 Big Bear 250 |
1996-2005 Big Bear 350 (2WD) |
1987-2008 Big Bear 350 (4WD) |
1987-2013 Big Bear 400 (4WD) |
2004-2006 Bruin 350 |
1995-2010 Wolverine 350 & 450 |
2007-2013 Grizzly 350 & 450 (4WD) |
2009-2012 Grizzly 550 (4WD) |
2007-2016 Grizzly 700 (4WD) |
1993-2004 Kodiak 400 & 450 |
2005-2006 Kodiak 400 & 450 (4WD) |
2004-2014 Rhino 450, 660, 700 |
For Suzuki |
2004-2009 Quadsport |
2002-2007 Eiger 400 |
2002-2007 Eiger Auto( not fit 2005) |
2002-2009 Ozark 250 |
2008-2016 King Quad 400 |
2001-2010 King Quad 450 |
2011-2016 King Quad 500 |
2005-2007 King Quad 700 |
2009-2016 King Quad 750 |
2003-2007 Vinson 500 |
For Bombardier |
2002-2004 Quest 500 |
1999-2004 Traxter 500 |
Can-Am (REAR ONLY) |
2008-2012 DS450 |
Package include:
2 Pcs Wheel Spacers
1 pair Gloves
1 x Steel Wire Ball
[Important Notes]
1. Check Your Vehicle Bolt Pattern/ PCD, Hub Bore Size, Thread Pitch, Vehicle fitment compatibility is only a guide.
2. Measure the fender gap and stock bolt length to choose suitable thickness.
3. PLEASE CONFIRM what you actuall need, wheel spacers or wheel adapters, they are different. Wheel Adapters are used to change bolt patterns in order to properly fit wheels from one vehicle to the hub of a different vehicle.
4. Do not use impact wrench.Please use hand wrench. Recommended to use threadlocker.
5. Returns are only accepted if unused and not installed.(ReturnsARE NOT ACCEPTED IF SPACERS-ADAPTERS HAVE BEEN INSTALLED TO YOUR VEHICLE)
-- Vehicle fitment compatibility is only a guide, please ensure that these are the correct ones for your vehicle.
-- For 1 inch or less or special adapters,
-- For 2 inches or more or special adapters,
If your vehicle requires 1" spacers but you purchased ≥2", the stock studs are shorter to hold the spacer safely, you need to exchange to small size adapters or purchase longer studs yourself.
What should I pay attention to during installation?
1) Check to make sure that the wheel spacer fits perfectly with the hub/axle stub and the inner mounting surface of the wheel.
2) Make sure that the wheel bolts being used are of the appropriate length, not too long or too short.
3) DO NOT proceed if both of the wheel spacer do not fit.
4) Please be sure to clean the rust on the hub before starting the installation, otherwise it will affect the working life of the spacers.
5) Make sure that you get 5-7 FULL TURNS of the lugs when installing. Torque them down to the manufacturers specs (up to and not greater than 110ft lbs).
6) Avoid using an impact wrench because improper usage may cause the lug nuts/bolts to break or loosen while driving causing a potential injury or accident.
7)All lug nuts, bolts and torque must be checked after driving the first 50 miles after installation. Afterwards, please check all lug nuts and bolts every 3,000-5,000 miles.
8) Alignment is necessary after installation, this will prevent any wobble and vibration from occurring.
