Cordless Dental Light Cure Lamp Light Metal Head LED 1S Curing Light
Product Description
Parameter
Wavelength440-480nm
Light power5W
Intensity800-1400mw/cm²
BatteryLi-on 800mAh
Input voltageAC100-240V, 50/60Hz 0.4A Max
Output voltageDC 5V/1.5A
Net Weight155g
Mode selectionP1, P2, P3
Solidification time1S,3S,5S,10S,15S,20S
Features:
·Produce the maximum light intensity safely.
· A high intensity of 1400 mW/cm2.
· Offers extremely short curing times of no more than 3 seconds.
· Cordless, highly portable and light weight (only 155g).
· High-performance Li-ion battery technology.
· LED panel conveniently indicates a countdown curing time.
· Battery can be fully recharged in 90 minutes.
· Battery with protection against over-voltage, over-current and short circuit.
· 3 versatile curing modes for every indications.
· Automatic power off, low battery alert.
· Color : White .
Operation conditions:
1.Storage Condition: Temperature: +10+40
2.Humidity: 30%-75%
3.Atmospheric pressure: 70KPa-106Kpa
4.Environment Conditions: Not near from fire equipment or flammability material.
Packing list:
The host * 1
Metal lamp holder *1
The silicone base *1
Power adapter *1
Disposable protective sleeve *1
Shade plate *1
Product specification *1
DX.Universal Dental Light Cure Composite Resin Kit Shade Etching Gel Adhesive
INDICATIONS FOR USE:
Direct restoration for all class caries.
Restoration of teeth defect and veneer.
REFILL:
Light Cure Composite: 4g/Syringe*5
Syringe Needles : 5pcs/ box*1
Total Etching Adhesive: 5ml/Bottle*1
Etching Gel: 2.5ml/Syringe*1
Applicators Brushes: 20pcs/box*1
Net weight: 188.4g
COLOR: A1,A2,A3,A3.5,B1
FEATURES & ADVANTAGES:
Unique dispersion technology ensure the filler evenly distributed
Radioopaque and fluoride releasing Optimal polishability and high shade stability.
Excellent handling, not sticky to instrument;
Suitable for most cases of restoration, extensive indication of usage.
INSTRUCTIONS:
(1) Preparation: isolate and prepare tooth.
(2) Cleaning: rinse the preparation with water.
(3) Drying: gently air dry until there is no visible water.Do not allow enamel or dentin to dry for an excessive period of time.
(4) Applying Dentex Self-Etching Light Cure Adhesive (DSA): dispense 1-2 drops of DSA into a mixing well, apply enough DSA to the entire preparation with a little brush until a shiny surface is achieved and then wait for 10 seconds (DSA should not be applied too much ). Use a gentle stream of air to evaporate the solvent for 5 seconds. (If using a non self-etching adhesive, an etching step should be used according to the manufacturer's instruction).
(5) Cure: light cure for 20 seconds at 500±50mW/cm2. Keep the distance to exposure surface less than 4 mm.
(6) Applying Dentex light cure composite (DLC): place selected DLC into cavity preparation following by light cure. According to following table, the curing time is recommended for different depth and color shades. In order to reduce shrinkage stress, for a large cavity, an increment filling is recommended. In general, 1-2 mm increments are placed into cavity preparation from different sides and the restoration is built incrementally. Each increment is light cured for 30 seconds.
(7) Finishing: after light cure, adjust restoration.
(8) Polishing: use polishing strip or disc to polish the surface
WARNING:
Do not use this product for patient who is allergy to methylmethacrylate. Do not use this product with any material contained eugenol.
PRECAUTIONS:
Methmethacrylate resins may cause skin sensitization in susceptible persons. In case of tell, wash skin with soap and water. In severe situation, get medical attention.
ATTENTION:
To an exposed pulp, a pulp capping material such as Calcium hydroxide may be used before using this product.
STORAGE:
Store at 25℃ or less in a cool and dry place and avoid direct sun exposure.
Recap the syringe after use.
DISPOSAL: After the product is used up, dispose it as normal medical rubbish.
SHELF LIFE: 3 years
Quantity: 1 Kit.
