Notes :
This is only a repair kit and cannot be used in its entirety.Please double confirm the compatibility as well as the OEM number before purchasing
Application:
Range Rover Sport
Compatible With ADS Electrical Plug
GT Limited Edition 3 Sport Utility 4-Door 5.0L 2012
GT Limited Edition Sport Utility 4-Door 5.0L 2011 2013
HSE Lux Sport Utility 4-Door 5.0L 2012-2013
HSE Sport Utility 4-Door 4.4L 2006-2009
HSE Sport Utility 4-Door 5.0L 2010-2013
LE Sport Utility 4-Door 4.2L 2008
Supercharged Sport Utility 4-Door 4.2L 2006-2009
Land Rover LR4
Base Sport Utility 4-Door 3.0L 2014-2016
Base Sport Utility 4-Door 5.0L 2011-2013
HSE Lux Sport Utility 4-Door 3.0L 2014-2016
HSE Lux Sport Utility 4-Door 5.0L 2012-2013
HSE Sport Utility 4-Door 3.0L 2014-2016
HSE Sport Utility 4-Door 5.0L 2010-2013
SE Sport Utility 4-Door 5.0L 2010-2013
V8 Sport Utility 4-Door 5.0L 2010
Land Rover LR3
Base Sport Utility 4-Door 4.0L 2006
HSE Lux Sport Utility 4-Door 4.4L 2009
HSE Sport Utility 4-Door 4.4L 2005-2009
SE Sport Utility 4-Door 4.0L 2005-2009
SE Sport Utility 4-Door 4.4L 2005-2009
OE Number:
RNB501580,RNB501180
RNB501220,RNB501250
RNB501480,RNB501610
RPD501480,LR016403
Generation & Evolution??
Land Rover Discovery
First generation (Project Jay; 1989-1998)
Second generation (LR2/L318; 1998-2004)
Third generation (LR3/L319; 2004-2009)
Fourth generation (LR4/L319; 2009-2016)
Fifth generation (L462; 2017-present)
Range Rover Sport
First generation (L320; 2005-2013)
Second generation (L494; 2013-present)
SVR (2015 Pre-Facelift)
SVR (2018 Facelift)
Platform Drive Layout:
Front Engine-Four Wheel Drive Layout
Signs that your air suspension needs to be replaced include:
1.Abnormal Sounds
2.Poor Handling Stability
3.Air Leakage
4.Car Body Slant
5.Irregular Tire Wear
6.Over Bend
Note Before Installation:
1.To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
2.Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
Removal Guideline:
Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
1.To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
2.Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
1.Set steering to straight ahead.
2.Raise vehicle.
3.Remove front wheels.
4.To release the air pressure from the front struts you will need to remove the right side front wheel well liner.
5.With the wheel well liner removed you are able to access the front valve block located on the rear of the wheel well. slowly release the air pressure from the front struts by loosening the yellow and black air hoses. (FIGURE 2)
6.Next, remove the brake hose and abs sensor wire from the retention bracket on the strut.
7.Also remove the sensor wire from the front side of the strut held on with a small plastic clip.
8.Disconnect the sway bar link by removing the nut holding the ball joint to the strut. you may need to hold the ball joint from spinning by placing a wrench on the two flats of the ball joint.
9.Remove the two large bolts that hold the strut to the spindle assembly.
10.With the nuts and bolts removed from the spindle assembly, pull the spindle outward while pushing the strut inward to disengage them.
11.For models equipped with vds, raise the hood to access the air strut's top damper; for models without, skip to step 16.
12.Remove the two (2) bolts holding the damper to the top of the air strut.
13.Remove the damper from the wire.
14.Remove the electrical plug from the top of the shock rod by pressing in on the two (2) sides and pulling up.
15.under the hood are the upper retention fasteners, remove all three being careful not to drop the strut.
16.With the strut removed you can now gain access to its hose connection, remove the fitting to free the assembly.
17.Removal complete.
Installation Guideline:
1.Install the new o-rings and o-ring spacers provided in the kit in the same orientation as removed in step 7.
2.Install the provided bumpstop over the strut shaft in the depicted orientation.
3.Slide the gold washer over the threaded end of the shock. Ensure the perimeter “lip” is facing downward away from the threads.
4.Slide the new air spring assembly over the shock. Make sure to align the plastic alignment pin on the air spring through the hole in the shock’s piston seat. After you have pushed the lower piston’s alignment pin through the shock’s spring plate, slide the external locking clip over the plastic pin to secure the air spring to the shock.
5.Push the upper black rubber mount over the shock’s shaft. Make sure to place the rubber seal in the correct orientation as depicted on page 11.
6.Slide the black washer over the treaded end of the shock. Ensure the perimeter “lip” is facing upward and towards the nut.
7.Thread the M16Nylon lock nut over the strut’s threaded shaft. You can tighten the nut using an impact wrench.
8.Install completed strut back into the vehicle in the reverse order of removal.
Highlight:
1. 100% Air Tightiness testing
2. 24 hours air tightness test ≤0.02MPa
3. Anti-corrosion and provide a more consistent wear surface
4. Built to strict quality control standards
5. CNC Machined Components
6. Designed for Comfort Suspension
7. Direct replacement for OEM strut without modification
8. Easy to install
9. Eliminating abnormal sound
10. Gives the driver more control of ride
11. Good heat dissipation
12. It has a high compressive strength and good sound insulation to ensure our driving comfort and safety
13. Restore the original ride height and improve ride quality
14. Test more than 3 million times
15. Sturdy & Durable Material
Package Included:
Single for Front Left or Right Air Suspension Spring Bag
Note:
1.Please double confim the compatibility as well as the OEM number before purchasing.
2.Instruction is not included. Professional installation is recommended
3.Please feel free to contact us for whatever we can help via eBay message; every message will be replied in 12 hours.
