Supercharger Kit for BMW N42, N43 and N46 engines 
for 
Eaton M62 Supercharger

Average power curve: 270 – 325 HP*

The NEMESIS I Supercharger Kit is designed around the Mercedes based Eaton M62 supercharger for the naturally aspirated 4-cylinder BMW N42, N43 and N46 Engines, filling a much desired gap.

This supercharger system supports a wide range of classic and Neo-modern BMW’s such as the E46 model as well as the E60, E81, E82, E83 X3, E84 X1, E85 Z4, E87, E88, E90, E91 models.


Additional information

Weight5 kg
Boost

Eaton M62: 7-14PSI*

Boost will depend on the pulley used on the supercharger, we recommend rebuilding the supercharger with new bearings if you wish to run it with a smaller pulley!

Chassis Fitment & Engines

All BMW 4-cylinder N42, N43 and N46 Engines, found in the classic BMW E46 models as well as Neo-modern BMW's such as the E60, E81, E82, E83 X3, E84 X1, E85 Z4, E87, E88, E90, E91 models.**

Not all models of chassis have been tested, if you would like to check with us your chassis measurements before buying, please email us.**

Notes:

For compatibility, you must use small body M62 with the short snout and small body variant commonly found in the Mercedes Kompressor models.

Supported Eaton M62 Supercharger Part #: A 1110900380, A1110900380, A 111 096 00 99 KZ, 111 0900080.

The Stock M62 pulley will limit the boost to 7PSI with an air to air intercooler, For 12-14 PSI you will have to rebuild the M62 Supercharger with new bearings and use the Hyde Motor Works 60mm or 70mm Overdrive pulley made for the M62 Supercharger. We recommend always using an intercooler and having a built engine to handle boost over 10PSI to avoid engine damage and wear.

NEMESIS I SUPERCHARGER KIT

The NEMESIS I was designed in Ireland between 2022 – 2023 by Werner Mayerhofer. This Supercharger Kit is designed to be used on the BMW 4 Cylinder N42 Engine with support for the N46 and N43. With full air to air intercooling support, this kit is capable of pushing the stock engine to its safe limits.

This kit comes with its own custom drive pulley, tensioner and independent belt drive which allows you to preserve all the original stock belt driven engine accessories as the alternator, power steering, air conditioner, all in their original position.

Includes:

  • Complete Set of Brackets
  • Inlet and Outlet manifolds for the M62 Supercharger
  • Custom Drive Pulley (Replaces Power Steering pulley)
  • Tensioner System with Independent Belt Drive
  • Idler Pulleys
  • Proper Gaskets – (Included with orders from fall 2024 on-wards)
  • Full set of Fasteners (nuts, bolts and spacers)
  • Finished in Powder Coated Raceway Red colour (Supercharger Kit)
  • Guaranteed 36 months craftsmanship warranty**

 

Supported BMW models & cars due to using 4-cylinder BMW N42, N46 engines:

  • 2001-2004 E46 316i and 316ti
  • 2001-2004 E46 318i/318Ci/318ti
  • 2004-2005 E46 316i/316ti
  • 2007-2008 E90 318i
  • 2005-2007 E87 118i
  • 2005-2007 E90/E91 318i
  • 2007-2011 E81/E87 118i
  • 2007-2013 E90 318i
  • 2004-2006 E46 318i, 318Ci and 318ti
  • 2004-2007 E83 X3 2.0i
  • 2005-2008 E85 Z4 2.0i
  • 2004-2007 E87 120i
  • 2005-2007 E90/E91 320i
  • 2007-2011 E81/E82/E87/E88 120i
  • 2007-2013 E90/E91/E92/E93 320i
  • 2007-2010 E60 520i
  • 2009-2015 E84 X1 sDrive18i / xDrive18i
  • 2007-2010 E83 X3 2.0i

 

NOTES:

  • Stock M62 pulley will limit the boost to 7PSI with an air to air intercooler, For 12-14 PSI you will have to rebuild the M62 Supercharger with new bearings and use the Hyde Motor Works 60mm or 70mm Overdrive pulley made for the M62 Supercharger.
  • Currently the kit supports only the Eaton M62 Supercharger, future support will be added for the Rotrex C15 and C30. *
  • The Supercharger is not included in the kit unless ordered separately from us, you are advised to use the given part number for the supercharger and order the supercharger locally.

 

To complete the installation on any of the setups, you will also require the following additional parts:

  • Eaton M62 Supercharger (Mercedes variant only, check the technical specifications for part numbers)
  • an Intercooler Kit with silicone pipes and hose clamps (can be sold separately)
  • vacuum hose
  • an high flow air filter
  • a boost gauge
  • a recirculating by pass valve and
  • proper tune.
May needs some modifications when installing.
(such as cutting, drilling, relocating some parts and etc.) 
It's NOT 100% PLUG and PLAY!!! 



Shipping Service:

Your order will be dispatched within 20 working days of receiving payment.



                       - PLEASE NOTE - 

I am NOT responsible for Custom fees, TAX or VAT or any delay with the country regulation would. Problems with customs on import. Retention of goods. Import bans in your country or during the shipping. Bans in your or other countries. The things listed are be the buyer responsibillity.

If you are NOT agree with them do NOT buy nothing for me!


Returns:

Returns are available!!! 

Please explore all the pictures very carefully! 

You will receive what you see! Nothiing more!!! Nothing less!