Mask it, spray it, leave it, peel it.
Designed to protect glass during all aspects of construction: residential, commercial, industrial, institutional, restoration and renovation. Suitable for outdoor use, not water based!
The USP of our product:
1.
Spray application via a lightweight, easy to
use 400ml spray can
2.
No training required
3.
Significant reduction in site waste, helping to
reduce carbon footprint
4.
Operating temperatures from -18°C to + 46°C
5.
100% waterproof ? Intended for internal and
external use
6.
Unlike window films will not delaminate from the glass surface, thus providing a
durable and long-
lasting protection
7. Quick and easy removal, simply peel away to remove.
How to Use Instructions
Site Shield film protective spray is intended for application onto glazed elements. It has been developed to offer a quick and effective means to prevent the typical scratching and marring of such surfaces that is ordinarily expected throughout the day-to-day operations on a construction site.
Once applied,
Site Shield provides a barrier
against detritus and other forms of
debris and prevents it from bonding directly to glass. After the coating system has performed
its intended role, it can be quickly and easily removed from the surfaces
onto which it has been applied. Our rational behind the development of Site Shield was to reduce the time of application, provide
the necessary levels
of protection to surfaces and keep
the removal time to a minimum. We hope that Site Shield meets your expectations and offers a new tool to overcome the unnecessary and costly consequences of glass
refurbishment and replacement.
In order to achieve the intended results,
we recommend the following application process:
1. Ensure that the area to be coated is dry and free of debris.
2. Pre-wipe any areas of exposed
uPVC with the provided wipe (Wipe A) See Note.
3.
Hold
the aerosol up to 300mm away from the surface.
4.
Spray horizontally in a left-to-right direction, covering the full surface.
5. Allow 10-30 seconds between
each coat ? dependent on ambient temperature.
6. We recommend three coats to provide full coverage, but more can be applied.
7. Remove any overspray from bare uPVC with the provided acetone wipes (Wipe
B) See
Note.
8.
The applied
coating will be fully cured
after 4-hours.
Note: Should uPVC elements of the window
frame not have the typical
factory applied film tape or, if
there are areas of the uPVC which are not covered
by the film tape, care should be taken to pre-protect
and to remove any overspray
of Site Shield
from the bare or unprotected areas of the uPVC.
It is therefore
necessary to ensure that Steps 2 and 7 above
are undertaken in full.
If Site Shield is left to dry on bare/unprotected uPVC for more than 24-hours, the provided acetone wipes
(Wipe B) and a light abrasive
agent such as T-Cut may be
required to restore plastics back to original form.
Disclaimer:
Site Shield takes no responsibility should these necessary steps not be followed.
To effectively remove the product
from the surface
it has been applied to take the following steps:
1. Starting from a corner, being to remove
the film coating.
2.
To aid in continuous film removal, keep as close to the surface as possible
whilst removing.
3. Any residual
film coating can be easily removed with an acetone
wipe.
4.
Buff
glass with a clean dry cloth.
5.
Removed film can be disposed of in a similar manner to other plastic materials
on site.
·
Always read the product label, including
storage instructions.
·
Adhere and obey site specific health and safety policies.
·
Personal Protective Equipment must be worn, including
eye protection, hand protection (nitrile gloves) and an FFP2 face mask. Exposed
skin in the immediate area of the spray
pattern should be covered i.e., arms.
·
For Glass surfaces only, do not spray on plastics, painted/varnished or, porous surfaces.
Should you have any questions or queries regarding Site Shield please contact us.
Could cover approximately 7.5 - 8 m2
Larger quantities available on request.
Suitable for outdoor use, not water based!