Title
Durable Radiator For Subaru Impreza WRX 2.0 2.5L EJ20 EJ25 4Cyl AT MT 2000-2007
 Durable Radiator For Subaru Impreza WRX 2.0 2.5L EJ20 EJ25 4Cyl AT MT 2000-2007
 

 
Item Description:
 
1.100% Brand New in Original Box
 
2.Premium OEM Quality Certified Factory
 
3.Direct Replacement
 
Fits: 

1998-2003 SUBARU LIBERTY  3nd Gen  2.0 / 2.5 4CYL

1998-2003 SUBARU OUTBACK 3nd Gen  2.0 / 2.5 4CYL

2000-2007 SUBARU IMPREZA  2.5 4CYL NON-TURBO

2000-2007 SUBARU IMPREZA  2.5 TURBO EJ20 / EJ25

2000-2007 SUBARU IMPREZA WRX  2.0 TURBO

2002-2007 SUBARU IMPREZA WRX STI 2.0 NON-TURBO

Core Size: 340 x 688 x 16mm

Inlet/Outlet:38mm/39mm

Transmission : Auto and Manual vehicles

NOTE:Some models do not need the bleed pipe on the top tank,we supply cap to block it off.

Fitment:
 
Make: SUBARU.
Engine: 2.0L 2.5L
Fuel: Petrol
 
 

How to Replace a Radiator :

  1. Preparation:

    • Park the vehicle on a flat surface, turn off the engine, and allow it to cool completely.
    • Gather necessary tools: socket set, wrench, screwdriver, drain pan, and the new radiator.
    • Disconnect the negative battery terminal for safety.
  2. Drain the Coolant:

    • Locate the Drain Plug: Place a drain pan under the radiator and open the drain plug at the bottom to drain the coolant. You may need to remove the radiator cap to allow the coolant to flow more easily.
    • Dispose of Coolant Properly: Collect the coolant in the drain pan and dispose of it according to local regulations.
  3. Remove the Old Radiator:

    • Disconnect the Radiator Hoses: Use a screwdriver or pliers to loosen the clamps on the upper and lower radiator hoses. Slide the hoses off the radiator connections.
    • Disconnect the Transmission Lines (if applicable): If your vehicle has an automatic transmission, disconnect the transmission cooler lines from the radiator.
    • Remove the Fan Shroud and Cooling Fans: If necessary, unbolt and remove the fan shroud and cooling fans to access the radiator.
    • Unbolt the Radiator: Remove the bolts or screws securing the radiator to the vehicle’s frame or support brackets.
    • Lift Out the Old Radiator: Carefully lift the radiator out of the engine bay, taking care not to spill any remaining coolant.
  4. Install the New Radiator:

    • Position the New Radiator: Place the new radiator in the same position as the old one, aligning it with the mounting points.
    • Bolt the Radiator in Place: Secure the radiator with the bolts or screws you removed earlier.
    • Reconnect the Hoses and Transmission Lines: Reattach the upper and lower radiator hoses, tightening the clamps securely. If applicable, reconnect the transmission cooler lines.
    • Reinstall the Fan Shroud and Cooling Fans: Reattach the fan shroud and cooling fans if they were removed.
  5. Refill the Coolant:

    • Close the Drain Plug: Ensure the radiator drain plug is closed.
    • Refill with Coolant: Pour fresh coolant into the radiator until it reaches the full mark. If necessary, also fill the coolant reservoir.
    • Bleed the Cooling System: Start the engine and let it run with the radiator cap off to allow air to escape. Add more coolant as needed.
  6. Check for Leaks and Test:

    • Inspect for Leaks: Check around the radiator, hoses, and connections for any signs of leaks.
    • Test Drive: After replacing the radiator, take the vehicle for a short test drive to ensure everything is functioning correctly and the engine stays at a normal operating temperature.

By following these steps, you can successfully replace the radiator in your vehicle, ensuring it cools the engine properly and operates efficiently.

 
PushAuction