12V 240A Car Remote Battery Disconnect Switch Automatic Power Shut Off Switch

Features:

【Low Power Consumption & Good Stability】:The parameters of kill switch for car are as follows: Rated current: 240A; Rated voltage: 12V; Standby power consumption: 3mA; Power failure threshold: 11.8V±0.2V; Instantaneous current: 500A.Battery kill switch Operating Temperature: -22℉~194℉

【Smart Voltage Safet Kill Switch】: This kill switch for car when the voltage is lower than 11.8V, it will cut off the power automatically after 120 seconds to save power; when the voltage is higher than 13.2V, the remote control is invalid and can only be controlled by a manual switch to prevent the power from being cut off by an accidental action during traveling. This kill switch for car adopts a new type of relay, which utilizes the magnetic principle to control the disconnection and cut-off of the circuit, and the standby current is 3mA, which is more energy-saving

【Protect and Extend Battery Life】: This kill switch for car can avoid car battery depletion due to long term parking, line aging, forgetting to turn off the lights and other reasons. this remote battery protects can maximize the retention of car battery power, effectively protect and extend the life of the car battery

【Magnetic Latching Function】:Remote battery disconnect switch is an upgraded version of the previous generation product,This kill switch for car uses a new type of relay that controls circuit disconnection by magnetic principle, with a standby current of 3mA, which is more energy-saving

【Application and Precautions】:This kill switch Suit for most 12V car, boat, rv, trailer, trucks, ATV, UTV, motorcycle, vehicles with displacement less than 4.0; Negative pole: 9-13 mm and 15-17mm, not fit for small pile head vehicles;Note: The size of the switch is 3.3"x2.4"x1.4", before order it, it's best to check and measure your car's battery compartment to see if there is enough space to install it and close the hood properly

 

NOTE: be sure to turn off the power before installation, ignition test after installation

Specifications

Type:Remote Battery Disconnect Switch

Color:Blue

Material:ABS

Battery disconnect switch rated current: 240A

Rated voltage: 12V

Standby power consumption: 3mA

Power-off threshold: 11.8V±0.2V

Instantaneous current: 500A

Operating Temperature: 30℃-90 ℃

Remote control frequency: 433mHZ

Function:  Long-term parking, power consumption of electronic devices, line aging, forgetting to turn off lights, etc. Disconnect Switches can solve the power consumption caused by such problems, and can extend the battery power and service life of cars.   

Package Content:

1 x Cut off Switch

2 x Remote controller

1 x cushioning sheet

1 x Manual

 

 

Remote control matching instructions:
 
1. Interlock mode (applicable to vehicle system control) - Press the manual button ON continuously for 3 seconds, and the code indicator light will flash 3 times to enter the learning mode. Press the button on the remote control, and the code indicator light will flash 3 times after successful code matching. Then press the other button on the remote control, and the code indicator light will flash 3 times after successful code matching;
2. After entering the learning mode, if the learning code indicator light does not receive a remote control signal within 30 seconds, it will automatically exit the learning mode;
3. Clear code - Long press the manual button ON to flash the code indicator light 8 times, indicating that the clear code is complete (long press the manual button ON to display the indicator light flashing 3 times, 4 times, 5 times, and 8 times in sequence; among them, flashing 3 times is the interlock mode learning state, flashing 4 times is the self-locking mode learning state, flashing 5 times is the jog mode learning state, flashing 8 times is the clear code state);
4. A set of 20 codes can be paired with 10 different remote controls simultaneously.

 

PushAuction