Item Description:
•Built to strict quality control standards
•Ready to use, Direct Replacement
•Superior quality parts
•100% Factory tested
Product Features:
- Vehicle bolt pattern: 6x5.5
- Spacer Thickness: 2 inch or 50 mm
- Torqued Down By Hand At: 70-80 FT/LBS
For the following years and models:
- For Acura:
- For Acura SLX 1996-1999
- For Chevrolet:
- For Chevrolet Colorado 2004-2014
- For Chevrolet LUV 1997-2005
- For Chevrolet S10 2016
- For Dodge:
- For Dodge D50 1979-1982
- For Dodge Ram 50 1985-1993
- For Ford:
- For Ford Ranger 2013-2022
- For GMC:
- For GMC Canyon 2004-2012
- For Honda:
- For Honda Passport 1994-2002
- For Hummer:
- For Hummer H3 2006-2010
- For Hummer H3T 2009-2010
- For Hyundai:
- For Hyundai Entourage 2007-2010
- For Hyundai H300 2016-2020
- For Hyundai Starex 2019-2020
- For Isuzu:
- For Isuzu Amigo 1989-1994&1998-2000
- For Isuzu i-280 2006
- For Isuzu i-290 2007-2008
- For Isuzu i-350 2006
- For Isuzu i-370 2007-2008
- For Isuzu Rodeo 1991-2004
- For Isuzu Rodeo Sport 2001-2003
- For Isuzu Trooper 1984 -2002
- For Kia:
- For Kia Sedona 2006-2012&2014
- For Lexus:
- For Lexus GX460 2010-2022
- For Lexus GX470 2003-2009
- For Mitsubishi:
- For Mitsubishi Montero 1989-2006&2008-2019
- For Mitsubishi Montero Sport 1997-2015&2018-2021
- For Toyota:
- For Toyota 4Runner 1989-2022
- For Toyota FJ Cruiser 2007-2014
- For Toyota Land Cruiser 1982-1997
- For Toyota Pickup 1980-1995 (4WD 6 Lug Vehicles ONLY)
- For Toyota Sequoia 2001-2007
- For Toyota T100 1993-1998
- For Toyota Tacoma 1995-2015 (4WD 6 Lug Vehicles ONLY)
- For Toyota Tacoma 2016-2022
- For Toyota Tundra 2000-2006
1 Year Warranty
If you dont't know the specific of your vehicle, pls confrim by following the below steps:
1) Check Vehicle Bolt Pattern/ PCD
For 4-lug, 6-lug, 8-lug, measure the segment from the center of a bolt hole to the center of another hole.
5-lug is different, you need to measure the segment from the outermost point (not center point) of a bolt hole to the center of another hole.
Take 5 lug for example, if the length of segment as measured in the picture is 5.5"/ 127mm, and as these are 5 lugs, then the bolt pattern is 5.5"/ 127mm.
2) Check Vehicle Hub Bore Size
Measure the diameter of the center bore, make sure the spacer's diameter is the same as or greater than the axle diameter.
3) Check Vehicle Thread Pitch
There are different types of studs, sunch as M14X1.5, M12X1.5, 1/2"x20, 9/16"x18, please make sure the studs of wheel spacers is the same as the vehicle's, otherwise the spacer will not fit.
We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US.We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
