WE’LL SUPPLY MATERIALS FOR YOUR PROJECT
FOCUS ON PLANNING & BUILDING
Ceresit ZU (Base Coat Render) Insulation and Mesh Adhesive 25kg
Ceresit ZU mortat is design to apply EPS-boards within Ceresit ETICS (External Insulation Composite Systems) with a light-wet method. ZU is part Cersit Ceretherm Popular. ZU mortar is used for applying to the EPS-boards as well as to prepare rainforced layer of newly erected objects anad the buildings to be thermo renovated.
During preparing the reinforced layer work on sunny walls is inadvisable. The layer should be protected from rain. Protection of scaffolding is recommended. Application should be performed in dry conditions with the substrate and ambient temperature from +5°C to +25°C. All the data refer ro the temperature of +20° and relative air humidity of 60%. Faster or slower setting of the mortar may occur in different conditions. ZU powder mortar shows irritated properties and cement and lime content causes alkali reaction whwen mixed with water. Therefore skin and eyes, they should be rinsed with water and the general practitioner should be consulted.
PLEASE NOTE
Instalattion
Other Items
- flexible
- durable
- good adhesion
- resistant to weather conditions
- possibility of machine application
ZU should be poured into the measured amount of cool clean water and stirred with the drill by means of a mixer until the homogenus is obtained without lumps.
1. Fixing EPS-boards
The ready mortar should be applied with a trowel along the board edges forming a strip of 3/4cm wide and a few spots with the diameter of approx. 8 cm. Then immediately, the board should be pressed to the wall with a few slight blows of a long float. The properly applied mortar when pressed should cover minimum 40% of its surface. In case of even, smooth substrates th mortar should be applied by means of a toothed long float (teeth 10-12mm). The boards should be fixed tightly one at the other in one surface with the preservation of "brick like manner" of vertical connection.
2. Preparing the reinforced layer
Prepared mortar should be applied 2-3mm layer on EPS-boards using smooth, steel trowel. On fresh layer glass fibre net should be set (10cm overlaps should be kept). Then the next layer can be applied (thickness 1mm) and smoothed in order to nest wasn't visible. Fresh stains should be cleaned with water while hardened elements should be mechanically removed only.
Up to 12 months since the production date when stored on pallets in dry cool conditions and in original undamaged packages.
COther items
FOCUS ON PLANNING & BUILDING
WE’LL SUPPLY MATERIALS FOR YOUR PROJECT
Ceresit ZU (Base Coat Render) Insulation and Mesh Adhesive 25kg
Ceresit ZU mortat is design to apply EPS-boards within Ceresit ETICS (External Insulation Composite Systems) with a light-wet method. ZU is part Cersit Ceretherm Popular. ZU mortar is used for applying to the EPS-boards as well as to prepare rainforced layer of newly erected objects anad the buildings to be thermo renovated.
PLEASE NOTE
During preparing the reinforced layer work on sunny walls is inadvisable. The layer should be protected from rain. Protection of scaffolding is recommended. Application should be performed in dry conditions with the substrate and ambient temperature from +5°C to +25°C. All the data refer ro the temperature of +20° and relative air humidity of 60%. Faster or slower setting of the mortar may occur in different conditions. ZU powder mortar shows irritated properties and cement and lime content causes alkali reaction whwen mixed with water. Therefore skin and eyes, they should be rinsed with water and the general practitioner should be consulted.
- flexible
- durable
- good adhesion
- resistant to weather conditions
- possibility of machine application
ZU should be poured into the measured amount of cool clean water and stirred with the drill by means of a mixer until the homogenus is obtained without lumps.
1. Fixing EPS-boards
The ready mortar should be applied with a trowel along the board edges forming a strip of 3/4cm wide and a few spots with the diameter of approx. 8 cm. Then immediately, the board should be pressed to the wall with a few slight blows of a long float. The properly applied mortar when pressed should cover minimum 40% of its surface. In case of even, smooth substrates th mortar should be applied by means of a toothed long float (teeth 10-12mm). The boards should be fixed tightly one at the other in one surface with the preservation of "brick like manner" of vertical connection.
2. Preparing the reinforced layer
Prepared mortar should be applied 2-3mm layer on EPS-boards using smooth, steel trowel. On fresh layer glass fibre net should be set (10cm overlaps should be kept). Then the next layer can be applied (thickness 1mm) and smoothed in order to nest wasn't visible. Fresh stains should be cleaned with water while hardened elements should be mechanically removed only.
Up to 12 months since the production date when stored on pallets in dry cool conditions and in original undamaged packages.
