Specifications：

 

Fits:For Jeep Grand Cherokee TJ Wrangler 4.0L V6 17749 17689 1999-2002

 

Starter Type: PMGR

Rotation: CW

Teeth: 10

KW: 1.2                                               

17749 SMT0077, M1T84381, M1T84382 56041012AB, 56041012AC, 56041012AD

 

Features：

 

1. Satisfy your needs for the performance of the starter on the basis of a reasonable price.

 

2. The long-lasting high-quality components can achieve the best performance.

 

3. The design conforms to the original specifications to suit its form and function.

 

4. Strict outbound inspection, quality assurance, and compliance with safety standards.

 

5. The starter has high power and high working efficiency.

 

6. Perfect after-sales service standards, you can contact us at any time if you have any questions.

 

Tips：

 

1. In the process of disassembly and assembly, avoid hitting the starter with hammers, wrenches and other tools to avoid damage to parts.

 

2. The disassembly and assembly of the starter must be carried out in accordance with the prescribed steps (the disassembly and assembly sequence of different types of starters are different, and should be carried out in accordance with the operating sequence specified by the manufacturer), especially the parts or assemblies that cannot be disassembled according to the disassembly operation. Do not disassemble arbitrarily (such as electromagnetic switch, stator core and winding).

 

3. When disassembling, carefully analyze the structure of the starter, the function of the components, the working principle, the assembly relationship and the connection of the circuit according to the requirements.

 

4.The disassembled parts should be arranged in order to avoid errors or omissions during assembly.

 

5.When assembling, each bolt should be tightened according to the specified torque. Check and adjust the gap of each part.

 

Notes：

 

1. When starting the engine, each turn-on time shall not exceed 5s. If continuous starting should be separated by 10-15s, the engine failure should be eliminated if the engine fails to start after three consecutive starts.

 

2. After confirming that the engine is not faulty, start again after an interval of 5 minutes, otherwise the heat generated by the starter due to the excessive starting current will not be dissipated, and the rotor and stator coils of the starter will be burnt.

 

3. When using the starter, it is necessary to keep all parts of the starter clean and dry, the connection is firm, the brush and the commutator are in good contact, and the maintenance should be checked and maintained regularly in accordance with the regulations of the car maintenance system. Mainly check the sliding bearing clearance at both ends of the starter, the one-way torque of the gear one-way device and the wear condition of the electric brush.

 

How to Install a Car Starter:

 

There’s never a convenient time for your vehicle’s starter to fail. A car starter's job is to kick over the engine in your car so your vehicle starts.When you find yourself with a vehicle that won’t start, there are a number of a number of issues that may be the culprit,but once you’ve narrowed it down to a faulty starter, you can replace it using just common hand tools.

 

Part 1: Removing a Bad Starter

(1).Disconnect the battery. 
You will not need to remove the positive cable on the battery.
Always disconnect the battery before servicing the electrical system in your vehicle.

 

(2).Jack up the vehicle if need be. 
Ensure you jack the vehicle up on firm, level ground.

 

(3).Locate the starter.
The smaller cylinder attached to the starter is the starter solenoid.
A wire should run directly from the positive terminal on the battery or from the fuse box under the hood to the top terminal on the starter solenoid.

 

(4).Disconnect the wiring to the solenoid. 
In some cases, it may just be clips you need to disconnect for the wiring.
On some starters, you will need to loosen bolts or screws that hold the wires in place.

 

(5).Remove the starter retaining bolts then the starter.
Be sure to use the correct size socket, otherwise you risk damaging the bolts.

 

(6).Compare the new starter to the old one.  Slide the starter into place. 
If the two starters don’t look mostly identical, it may not be the correct starter for your vehicle.
New starter solenoids often come with four terminals, but can be used with only two.

 

Part 2: Installing a New Starter

 

(7).Insert the starter retainer bolts. 
If the bolt does not thread properly, unscrew it and try again.
Make sure the bolts are tight so they can’t vibrate loose while the engine is running.

 

(8).Connect the wiring to the starter solenoid. 
With the starter secured in place, reconnect the wiring you disconnected from the old starter onto the terminals on the new one. If your new solenoid has four terminals but your old one had two, only utilize the top and bottom terminal on the new solenoid. If your old one had four and the new one does as well, connect them to the same terminals they were connected to on the old one.

 

(9).Reconnect the battery. 
With the starter installed and wired, reconnect the black cable to the negative terminal on the battery and tighten it in place. Insert the key into the ignition and attempt to start the vehicle.
If the vehicle fails to start with the new starter in place, ensure the battery is fully charged.

 

(10).Listen to the vehicle as you attempt to start it. 
As you turn the key in the ignition, listen for the sounds the engine makes to help determine if you have an issue with your starter. If the engine makes no sound whatsoever, or you hear only a faint clicking, it may be because there isn’t enough power reaching the electric starter motor.

 

(11).Ensure the battery terminals are clean and secure.Charge your vehicle’s battery. 
A weak connection from the battery can prevent the engine from starting.
Wear gloves when cleaning battery terminals to avoid getting battery acid on your skin.

If you suspect the battery may simply be low on power, try charging it using either a trickle charger or another vehicle to jump start it. Be sure to connect the red cable to the positive terminal on each vehicle and the black to the negative.

 

(12).Check to see the starter solenoid is bad. 
If the test light does not light up, it means power is not reaching the starter motor due to a faulty solenoid or a dead battery.
If the test light does light up, it means the solenoid is good, but the starter itself may have failed.

 

Frequently Asked Questions:

(1).Why is my car starter burning out?
You likely cranked the starter for too long.

 

(2).I have to change the starter fairly often in my car. What could be causing this?
A leak of some sort could be fouling the starter if fluid is dripping on it. If that's the case,

replacing the starter doesn't fix the leak so it's only a matter of time before the new starter fails.

 

(3).What is the black wire connected to?
He black wire can be commonly associated with the wire that connects the battery to the ignition.

If this is not the wi