ZF 8HP45 APPLICATIONS (2011-2023):

BMW:

• 3 Series F30 (2012-2018): 320i, 328i, 330i, 335i

• 4 Series F32/F33/F36 (2014-2020): 428i, 430i, 435i

• 5 Series F10 (2011-2017): 528i, 530i, 535i

• X3 F25 (2011-2017): xDrive28i, xDrive35i

• X4 F26 (2015-2018): xDrive28i, xDrive35i

• ZF Part Numbers: 8HP45 000 001 - 8HP45 000 299

AUDI/VOLKSWAGEN:

• Audi A4 B8 (2011-2015): 2.0T FSI

• Audi A5 8T (2011-2016): 2.0T FSI

• Volkswagen Touareg (2011-2018): 3.6L FSI

• Transmission Codes: MY8HP45Z, MY8HP45A

ZF 8HP70 APPLICATIONS (2010-2023):

BMW:

• 5 Series F10 (2011-2017): 550i

• 6 Series F06/F12/F13 (2012-2018): 650i

• 7 Series F01/F02 (2010-2015): 750i, 750Li

• X5 F15 (2014-2018): xDrive50i, M50d

• X6 F16 (2015-2019): xDrive50i

• ZF Part Numbers: 8HP70 000 001 - 8HP70 000 499

AUDI:

• Audi A8 D4 (2011-2017): 4.0T FSI

• Audi S6/S7 (2012-2018): 4.0T FSI

• Audi RS7 (2014-2018): 4.0T FSI

• Audi Q7 (2015-2020): 3.0T, 4.0T

• Transmission Codes: MY8HP70Z, MY8HP70A

JAGUAR/LAND ROVER:

• Jaguar F-Pace (2017-2023): 3.0L SC

• Jaguar XJ (2011-2019): 5.0L SC

• Range Rover Sport (2014-2022): 3.0L SDV6, 5.0L SC

• Transmission Codes: 8HP70 500 001 - 8HP70 500 299

ZF 8HP90 APPLICATIONS (2015-2023):

BMW:

• 7 Series G11/G12 (2016-2022): 750i, 750Li

• X7 G07 (2019-2023): xDrive50i

• 8 Series G15 (2019-2023): 850i

• ZF Part Numbers: 8HP90 000 001 - 8HP90 000 199

ROLLS ROYCE:

• Ghost (2010-2020)

• Wraith (2013-2020)

• Transmission Codes: 8HP90 800 001 - 8HP90 800 099

TECHNICAL SPECIFICATIONS & SERVICE DATA

FLUID PROPERTIES:

• OEM Approval: ZF TE-ML 14A, 14B

• Base Oil: Full Synthetic PAO

• Additive Package: Advanced anti-wear (ZDDP), anti-foam, corrosion inhibitors

• Shear Stability: Excellent resistance to viscosity breakdown

• Oxidation Stability: 2000+ hours in ASTM D943 test

FILTER PERFORMANCE:

• Filtration Efficiency: 98% at 25 microns

• Burst Pressure: 450 PSI minimum

• Flow Rate: 12 GPM at 20 PSI pressure drop

• Temperature Range: -40°C to 150°C

• Media Material: Glass-reinforced synthetic fiber

SERVICE INTERVALS:

• ZF Recommended: 80,000 miles or 8 years

• Severe Service: 60,000 miles (towing, performance use, taxi service)

• Fluid Capacity: 7L allows static exchange 

• Actual Transmission Capacity: 8HP45: 9.5L | 8HP70: 10.5L | 8HP90: 11.0L - if you are planing for dynamic exchange check my other listings for more oil

PROFESSIONAL INSTALLATION PROCEDURE

PRE-SERVICE CHECKS:

1. Verify Transmission Model: Located on transmission ID tag (driver's side of transmission case)

2. Check Current Fluid Condition: Smell, color, contamination

3. Inspect for Leaks: Check pan, cooler lines, output seals, electrical connectors

4. Scan for Codes: Read and document transmission fault codes

5. Record Adaptation Values: Note current shift adaptations for comparison

DRAIN & REFILL PROCEDURE:

1. Warm Transmission: Operate vehicle until ATF reaches 30-40°C (86-104°F)

2. Secure Vehicle: Level surface, parking brake set, wheels chocked

3. Remove Transmission Pan: Carefully lower pan to drain fluid into approved container

4. Inspect Old Fluid: Check for metal particles, clutch material, debris

5. Clean Mating Surfaces: Use brake cleaner and lint-free cloth

6. Replace Filter: Install new filter with integrated gasket - hand-tighten bolts first

7. Torque Bolts: 8 Nm (71 in-lb) in criss-cross pattern in 3 stages

8. Initial Fill: Add 5-6 liters through fill port using fluid pump

9. Cycle Transmission: Start engine, shift through all gears with brake applied

10. Final Fill: Add fluid until steady stream from overflow at 35-45°C (95-113°F)

POST-SERVICE PROCEDURES:

• Reset Adaptation Values: Using professional diagnostic tool (ISTA, Autel, Snap-on)

• Road Test: Verify proper shift operation through all gears

• Re-check Fluid Level: After cooling to ambient temperature

• Final Leak Check: Inspect for any seepage or drips after test drive

• Document Service: Record mileage, date, and fluid used

 IMPORTANT TECHNICAL NOTES

CRITICAL WARNINGS:

• NOT for 6HP transmissions ? requires different fluid specification (Top Tec 1200)

• Fluid temperature MUST be monitored during fill procedure ? use infrared thermometer

• Use only approved fluids ? incorrect fluid causes immediate clutch pack damage

• Reset adaptations required for optimal shift quality and relearn

• Do not over-tighten pan bolts ? aluminum threads strip easily

PERFORMANCE BENEFITS:

• Smoother Shifting: Reduced clutch engagement time by 15-20%

• Improved Longevity: 40% longer fluid life vs. conventional ATF

• Enhanced Protection: Superior thermal stability reduces oxidation

• Fuel Economy: Reduced friction improves efficiency by 2-3%

• Temperature Management: Better heat dissipation in high-stress conditions

 SHIPPING & SUPPORT INFORMATION

PROFESSIONAL SUPPORT:

• Technical Assistance: Message us for installation guidance with 2-hour response time

• Diagnostic Support: Help with adaptation resets and coding issues

• Same-Day Response: Guaranteed within 24 hours, usually within 2-4 hours

SHIPPING DETAILS:

• Processing Time: Same day for orders before 3PM EST

• Packaging: Professional, leak-proof containers 

• Carrier Options: UPS Ground, FedEx 2Day, USPS Priority available

• Tracking: Provided immediately upon shipment with delivery updates

• International: Available to Canada, UK, EU, Australia ? message for quote

 READY FOR PROFESSIONAL-QUALITY TRANSMISSION SERVICE?
Add to Cart Now for Smoother Shifting and Extended Transmission Life!