Specifications:
 
The working state of the cold piece is that one side is cooling and the other is heating. The heating surface must be well dissipated during work. It is strictly forbidden to turn on the power for more than 5 seconds without heat dissipation.
 
When installing the radiator, be sure to apply thermal grease.
 
There are literals for cold Side, and no literals for hot side.
 
If you don't know the hot and cold side, you can use a 1.5V dry battery to test it. After a few seconds of power on, the hot side (without literal) will be hot, and the cold side (with literal) will be cold.
 
A radiator or a water cooling device must be installed on the heat dissipation surface, otherwise it will burn.
 
 


Chip model: TEC1-12703
Dimensions: 40*40*4.0mm±0.1, the number of pairs of components is 127
Wire specifications: lead length 310mm±5mm, RV standard wire, 5mm tinned single end
Internal resistance: 4.0~4.3Ω (ambient temperature 23±1℃, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 63℃
Working current: Imax=3A (when 15.5V starts)
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax27W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around

Chip model: TEC1-12704
Dimensions: 40*40*3.6mm, the number of pairs of components is 127
Wire specifications: lead length 300±5mm, RV standard wire, single end 5mm, tinned
Internal resistance: 3.0~3.3Ω (ambient temperature 23±1°C, 1KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 63°C
Working current: lmax=4A (when 15.5V starts)
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 36W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around

Chip model: TEC1-12705
Dimensions: 40*40*3.84mm, the number of pairs of components is 127
Wire specifications: lead length 100±5mm, RV standard wire, single end 5mm, tinned
Internal resistance: 2.4~2.7Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (QC=0) above 61°C
Working current: ImaX=5 (at 15.5V startup)
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 30W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around

Chip model: TEC1-12706
Dimensions: 40*40*3.67mm, the number of pairs of components is 127
Wire specifications: lead length 300±5mm, RV standard wire, single head 5mm, tinned
Internal resistance: 2.0~2.2Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 62℃
Working current: Imax=6 (4.5A at rated voltage startup)
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 60W
Assembly pressure: 85Ncm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around

Chip model: TEC1-12707
Dimensions: 40*40*3.64mm, the number of pairs of components is 127
Wire specifications: lead length 300±5mm, RV standard wire, 5mm tinned single end
Internal resistance: 1.8~2.0Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 62°C
Working current: Imax=7A
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 67W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around
 
Chip model: TEC1-12708
Dimensions: 40*40*3.6mm, the number of pairs of components is 127
Wire specifications: lead length 300±8mm, RV standard wire, 5mm tinned single end
Internal resistance: 1.5~1.7Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 60°C
Working current: Imax=8A
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 77W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around
 
Chip model: TEC1-12709
Dimensions: 40*40*3.6mm, the number of pairs of components is 127
Wire specifications: lead length 200±5mm, RV standard wire, 5mm tinned single end
Internal resistance: 1.3~1.5Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 61°C
Working current: Imax=9A
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 85W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around
 
Chip model: TEC1-12710
Dimensions: 40*40*3.4mm, the number of pairs of components is 127
Wire specifications: lead length 300±8mm, RV standard wire, 5mm tinned single end
Internal resistance: 1.2~1.3Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 60°C
Working current: Imax=10A
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 85W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around
 
Chip model: TEC1-12712
Dimensions: 40*40*3.2mm, the number of pairs of components is 127
Wire specifications: lead length 200±8mm, RV standard wire, 5mm tinned single end
Internal resistance: 1.0~1.1Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: △Tmax (Qc=0) above 62°C
Working current: Imax=9.5A
Rated voltage: DC12V (Vmax: 15.5V)
Cooling power: Qcmax 114W
Assembly pressure: 85N/cm2
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around
 
Chip model: TEC1-19906
Dimensions: 40*40*3.6mm, 199 pairs of components
Wire specifications: lead length 155±8mm, soft silicone wire, single-ended 5mm tinned
Internal resistance: 3.0-3.2Ω (ambient temperature 23±1°C, 1 KHZ, AC test)
Maximum temperature difference: above 63°C
Maximum current: ImaX=6A
Maximum voltage: 24V
Assembly pressure: 85N/cm2
Maximum temperature resistance: 200°C. For normal cooling work, the heat dissipation surface needs to be controlled within 50 degrees
Working environment: temperature range -55°C~83°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard epoxy resin sealing around
 
Chip model: TEC1-12706 (high quality)
Dimensions: 40*40*4.0±0.1mm, the number of components is 127
Wire specifications: lead length 110±5mm
Internal resistance: 2.0~2.2Ω (ambient temperature 23±1°C, 1 KHZ AC test)
Maximum temperature difference: ≥65°C
Maximum current: 6A
Maximum voltage: 15.4V
Cooling power: 53.4W
Assembly pressure: 85Ncm2
Working environment: temperature range -50°C~80°C (excessive ambient temperature will directly affect cooling efficiency)
Encapsulation process: standard 704 silicone rubber seal around


12V semiconductor refrigeration sheet product introduction:
Semiconductor coolers bring us a new concept of heat dissipation, so that the temperature of the CPU can be further controlled. With the advent of summer and the rise of ambient temperature, overclocking enthusiasts want to further improve the cooling conditions of the CPU. When the semiconductor cooler is powered on, there will be a certain temperature difference between the plates at both ends. The cooling surface provides a cool environment for the CPU.
Semiconductor refrigerators have many uses, and can be used to make portable refrigerators/incubators, hot and cold water dispensers, etc. Also used for heat dissipation of electronic devices. At present, the semiconductor material used in the refrigerator is mainly bismuth telluride, and the impurity is added to form an N-type or P-type semiconductor temperature difference element after special treatment. Taking the common TEC1-12605 in the market as an example, its rated voltage is 2V, its rated current is 5A, its temperature difference can reach 60 degrees Celsius, its dimensions are 40X40X0.4cm, and its weight is about 25 grams. Its working characteristic is that one side is cooling and the other side is heating.
After the DC power supply is turned on, the electrons start from the negative electrode (-), first pass through the P-type semiconductor, absorb heat here, and then release the heat when it reaches the N-type semiconductor. On the other side, a temperature difference is caused, thus forming a hot and cold end.

Package Including:According to your choose. Choose your need from above drop down menu.  
 
Payment:
We accept Paypal only, It is fast, Easy and Safe.
Payment must be completed within 7 days.
PLEASE NOTE: S&H DOES NOT INCLUDE DUTIES, LOCATL TAXES OR ANY OTHER IMPORTATION FEES.
Please list your special requests (color, packages, etc.) in the PAYPAL NOTES SECTION when you make payment.
Shipping:
We Ship to Worldwide.
Orders processed within 24-48 hours of payment verification. it will take 15-25 days for delivery. but Customs will random inspection some parcel, so that's why some parcel need more than four weeks to arrive. Shipping time is only estimated and not guaranteed.
We only ship to confirmed PAYPAL addresses. Your PAYPAL address MUST MATCH your Shipping address.
Package to USA will Shipping by E-Package with Tracking Number(7-15 Days to Delivered). To other Countries will shipping by Post Air Mail without tracking number(ONLY when the order is over 20USD will supply Tracking Number Shipping Way!)(15-35 Days to Delivered)
Items are shipped via China Post Air Mail.
Guarantee:
Good Good quality. Buy with confidence!
If you are not satisfied when you receive your item, please return it within 7 days for a replacement or money back. Please contact me before you return it.
Not accept returning of electronic components.
Full refund after we receive our original item, Note: Return shipping is to be paid by the Buyer.
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
PushAuction