Touch Switch UT19T11 Stepless Dimming Switch, LED ON When Device ON, Suitable for 19mm 3/4" Mounting Hole
Product Details
- Operation Mode: ON-NONE-ON
- Current Rating: 7 Amps
- Operating Voltage: 24 Volts
- Contact Type: Normally Open
- Connector Type: Wires
- Brand: Ulincos
- Switch Type: Touch Switch
- Terminal: Pins
- Material: Stainless Steel
- Item dimensions L x W x H: 7.09 x 0.87 x 0.87 inches
- Operation Mode: ON-NONE-ON
- Current Rating: 7 Amps
- Operating Voltage: 24 Volts
- Contact Type: Normally Open
- Connector Type: Wires
- Brand: Ulincos
- Terminal: Pins
- Item dimensions L x W x H: 7.09 x 0.87 x 0.87 inches
- Circuit Type: 1-way
- Actuator Type: Touch
- Contact Material: Copper
- Number of Positions: 2
- Control Method: Touch
- Connectivity Protocol: X-10
- Color: LED ON when device ON
- Wattage: 168 watts
- Unit Count: 1 Count
- Manufacturer: Ulincos
- Vehicle Service Type: Varies by Vehicle Type
- Control Type: Touch
- Compatible Devices: Lights (DC 6-24V, up to 7A)
- UPC: 711508302090
- Product Dimensions: 7.09 x 0.87 x 0.87 inches
- Item Weight: 1.58 ounces
- Item model number: UT19
- Is Discontinued By Manufacturer: No
- Date First Available: November 7, 2018
- Touch switch, just touch it!
- Stepless Dimming Type: You can Click or Holding Touch the switch to control your lights
- LED is ON when device is ON ! The other functions are the same as UT19T1.
- The wires replace the terminal pins, make installing very easy
- Dimming Switch, normally be used to control the lights. Don't exceed the rating amps and volts, you can run it on your other projects.
What You Get: 1 Touch Switch 1 Instruction What's the Touch Switch: Touch switch, just touch it! The touch switch is rated for 7A MAX /DC 6-24V. What's the Touch Switch Used for: Most often the Stepless Dimming switch is used for lights (Such as critical lights, chassis lamp, dome light) About Stepless Dimming type: 1.The light (device) is off when connecting to electricity. Click it (time <550ms) once to initiate it with the light on. Click it again to let it be off. Continue to cycle. 2.The initial brightness is 100% of the maximum brightness. 3.Touch and hold it (time > 550ms) to initiate stepless dimming control. The brightness increases when touching and holding, and stays at the level when stop holding. When holding more than 3 seconds, the brightness reaches and stays at maximum level. The brightness decreases when touching and holding again, and stays at the level when stop holding. When holding more than 3 seconds, the brightness reaches and stays at minimum level. Continue to cycle. 4.Click and Holding Touch can be used anytime. There is no interference between these two functions. What's Note: The touch switch can't be used on a pump.It will be burnt out easily. If you meet the static electricity problem, you can let the switch housing be grounded. The touch switch doesn't work with wet or damp fingers. The touch switch cannot be used in AC circuit. Don't exceed the rating volts! Make sure your wiring is correct! Specifications: Head diameter: 7/8" ( 22mm ) Mounting hole size: 3/4" ( 19mm ) Depth inc contacts: 1.1" ( 28mm ) Switch Type: Stepless Dimming Input Voltage: DC 6V-24V Output Current: 7A MAX LED color: Blue (LED ON when device ON) Enclosure material: Stainless Steel Protection level: IK10 Operating Temperature: -20℃ ～ +55℃
