What can foxwell SD-Series Smoke Leak Detector do?
Freauent refilling oil/coolant
Car Dashboard lights up
Small something weird
Engine running too hot
and more
Use Foxwell Smoke Leak Detector can Accurately detect the location of the leak.

Foxwell SD-Series Smoke Leak Detector Support Muilti-systems Test
EVAP System Test
Intake System Test
Exhaust Systems Test
Crankcase system test
Car Sealing Test
Fuel Tank System Test
Various Pipe Fittings Test

Wide Range of Applications: 
suitable for detecting pipeline system leaks on cars, motorcycles, snowmobiles, beach bikes, light trucks, heavy-duty trucks, and speedboats. Supports all 12V vehicle batteries.

Overheat and Antifreeze Protection:
The smoke detector is equipped with the latest intelligent protection devices. When the temperature of the equipment exceeds 75 degrees Celsius, the power protection device will intelligently start and shut down to ensure the safety of the operator and equipment. If the device operates continuously for more than 15 minutes, it will be protected from overheating for a protection time greater than 10 minutes. This device is also suitable for low-temperature operation. Only car batteries with a full capacity of 12V are supported.

How to Test It?
1. Inject 10ml-20ml of test oil into the smoke leak detector, filling 20ML of test fluid, under standard working conditions, can be used continuously for about 10 minutes; (about Smoke Oil: advise use the Baby oil)
2. Open the pipe that needs to be connected with the leak detector.
3. Install the airbag adapter into the sealed pipe and connect the device to the smoke conduit.
4. Connect the leak detector to the DC12V battery and the device will start working. NOTE: red clamp tp positive(+), and black clamp to negative(-)
5. The pipe will be filled with smoke and the leakage point will be checked.
6. Test the leaking pipeline, under the premise of sealing accurately, generally about 1 minute can be filled with smoke, if there is a leak, within 3 minutes, you can observe the results.

Caution:
1. When you use this Car Smoke Leak Detector for the first time, fill with 10-20ml baby oil. Please be careful NOT to beyond this range.
 2. Fresh oil can be filled with only when the smoke gets thin, and it can't be filled over 20ml each time.
 3 . Before filling fresh oil, please pour out the left oil in the detector & replace the detector oil regularly.
 4. During the process of leak detection, please keep away from smoke-sensitive parts.
5. Do NOT run the detector over 8 minutes continuously. It needs interval rest.
 6. The detector has an intelligent protector, if it exceeds the working limit, such as over 75 ℃, it will automatically turn off the power. In this case, please operate it later.
 7. The round part of this detector has temperature, please be careful to avoid burns.
 8.  If the test pipe needs to be disconnected in the middle, please sE~Ure the other side with a rubber stopple.

A- SD101 Packing List:

1pc Foxwell SD101 Main Unit
1pc Funnel
1pc Smoke Tube
1pc Power Cord
1 set Cap Plugs Kits
1 set EVAP Test Connector
1pc Hook
1pc User Manual  

B-SD101 PRO Packing List:
1x SD101 PRO Main Unit
1x Box
1x Funnel
1x Hook
1x Smoke Tube
1x Cap Stoppers (8 Pcs)
1x EVAP Test Connetor
1x Power Cords
1x EVAP Test Kit
1x  User's Manaul

 

C-SD201 Packing List:

1pc Foxwell SD201 Main Unit
1pc Funnel
1pc Smoke Tube
1pc Power Cord
1pc Hook
1pc User Manual  
1pc  Inflatable Adaptor
1pc  Intake Adaptor Cord
1pc  Air Drum Rubber

 

D-SD203 Packing List:

1pc Foxwell SD203 Main Unit
1pc Funnel
1pc Smoke Tube
1pc Power Cord
1pc Hook
1pc User Manual  
1pc  Inflatable Adaptor
1pc  Intake Adaptor Cord
1pc  Air Drum Rubber