Description
N1201SA+ Antenna RF Vector Analyzer High Performance RF Vector Impedance Analyzer 34.375MHz ~ 2700MHz
Specification:
- Model: N1201SA+
- Working frequency: 34.375MHz ~ 2700MHz
- The frequency step by step: 1kHz
- Display: 2.4inch TFT resolution 320 x 240 (QVGA)
- Battery capacity: 2000mAH (7.4Wh)
- Power consumption: <1.5W
- Charging current: 400mA
- Charger port: USB (only act as charger port)
- Automatic shut-down: can be set (it has been open for 5 minutes ~ 60 minutes optional)
- Measurement parameters: resistance, reactance, standing, s11
- Resolution: four significant figures
- Frequency accuracy: < ±3ppm
- Connector: SMA - K
- Measurement range:
Impedance: 0.1ohm ~ 1000ohm (The absolute value of impedance)
Standing: 1.000~65
S11(dB): 0dB ~ -60dB
- Directivity: < 35dB (140MHz ~ 2GHz calibrated), < 30dB (2GHz ~ 2.7GHz)
- Scan points: 280
- Output level: -18dBm
- Work temperature: 0℃~40℃
- Atmospheric pressure: 860hPa ~ 1060hPa
Caution:
- Interface: The analyzer has four interfaces in total: single point measurement, scanning function, system information, calibration and calibration of cable length measurement and characteristic impedance measurement interface is unique to N120SA+. It will enter the single-point measurement interface by default when it is powered on. The setting parameters are automatically saved after the product is powered off. When the product is powered on again, the settings of the interface are completely the same as before the power off, which is convenient to use.
- Switch on/off: press the CTRL key and then turn on/off.
In the power-on state, press and hold the (2S or above) switch on/off key. After releasing, the analog device will be shut down.
- Charging: Due to the high power consumption of this device, the battery capacity is also large. The designed charging current limit is 400mA. It takes about 5 hours to fully discharge until the charging is completed. If the battery is switched on when charging, the overall current consumption is about 750mA, so in order to be able to charge normally, please select a mobile phone charger with a current output capacity of more than 1A for charging. After the analog battery is out of power, please charge it in time to avoid damaging the battery. If it is not used for a long time, it is recommended to charge it every 1 year to avoid battery failure.
- RF interface: The RF interface is SMAK. Since the strength of copper is relatively lower than that of other metals, please try to protect it carefully to avoid falling and pulling.
More information:
- User manual: http://pan.baidu.com/s/1eSwfj0Y
Package Included:
- 1 x Host
- 1 x Data Cable
- 1 x User Manual
200 ohm resistance test 140MHz
Frequency scanning diagram of 200 ohm resistance
8.2pF capacitance test at 140MHz
8.2pF capacitance test at 440MHz
8.2pF capacitance test at 940MHz
8.2pF capacitance test at 2GHz
Specification:
- Model: N1201SA+
- Working frequency: 34.375MHz ~ 2700MHz
- The frequency step by step: 1kHz
- Display: 2.4inch TFT resolution 320 x 240 (QVGA)
- Battery capacity: 2000mAH (7.4Wh)
- Power consumption: <1.5W
- Charging current: 400mA
- Charger port: USB (only act as charger port)
- Automatic shut-down: can be set (it has been open for 5 minutes ~ 60 minutes optional)
- Measurement parameters: resistance, reactance, standing, s11
- Resolution: four significant figures
- Frequency accuracy: < ±3ppm
- Connector: SMA - K
- Measurement range:
Impedance: 0.1ohm ~ 1000ohm (The absolute value of impedance)
Standing: 1.000~65
S11(dB): 0dB ~ -60dB
- Directivity: < 35dB (140MHz ~ 2GHz calibrated), < 30dB (2GHz ~ 2.7GHz)
- Scan points: 280
- Output level: -18dBm
- Work temperature: 0℃~40℃
- Atmospheric pressure: 860hPa ~ 1060hPa
Caution:
- Interface: The analyzer has four interfaces in total: single point measurement, scanning function, system information, calibration and calibration of cable length measurement and characteristic impedance measurement interface is unique to N120SA+. It will enter the single-point measurement interface by default when it is powered on. The setting parameters are automatically saved after the product is powered off. When the product is powered on again, the settings of the interface are completely the same as before the power off, which is convenient to use.
- Switch on/off: press the CTRL key and then turn on/off.
In the power-on state, press and hold the (2S or above) switch on/off key. After releasing, the analog device will be shut down.
- Charging: Due to the high power consumption of this device, the battery capacity is also large. The designed charging current limit is 400mA. It takes about 5 hours to fully discharge until the charging is completed. If the battery is switched on when charging, the overall current consumption is about 750mA, so in order to be able to charge normally, please select a mobile phone charger with a current output capacity of more than 1A for charging. After the analog battery is out of power, please charge it in time to avoid damaging the battery. If it is not used for a long time, it is recommended to charge it every 1 year to avoid battery failure.
- RF interface: The RF interface is SMAK. Since the strength of copper is relatively lower than that of other metals, please try to protect it carefully to avoid falling and pulling.
More information:
- User manual: http://pan.baidu.com/s/1eSwfj0Y
Package Included:
- 1 x Host
- 1 x Data Cable
- 1 x User Manual
200 ohm resistance test 140MHz
Frequency scanning diagram of 200 ohm resistance
8.2pF capacitance test at 140MHz
8.2pF capacitance test at 440MHz
8.2pF capacitance test at 940MHz
8.2pF capacitance test at 2GHz
Payment Terms
1. We accept PayPal,Payoneer,Visa Card,Google pay,Credit card etc.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
1. We will process the order within the handling time ,if you have any questions, please contact us via eBay message or email.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
Return Terms
If you receive the item that not satisfied or defective, please do not open case and kindly notify us within 30 days. We will guide you the returning process for replacement or refund.
Custom Duties & Taxes
1. It is buyer's responsibility to cover the import duties, taxes.We do not charge any taxes and fees, and the possible taxes and fees will be collected by the platform or by third parties such as customs and carriers.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
Feedback
1. Please kindly leave us a positive feedback and 5 star DSR if you satisfied with our product and service. Please feel free to contact us firstly if you have any problem with your order, we are responsible and credible seller and will solve the issue it for you asap.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
On Sep 4, 2025 at 01:41:29 PDT, seller added the following information: