- Auto Parts Zone is one of the fast-growing automotive aftermarket parts online providers in America. With more than 25 years experience in the industry, All parts will meet or exceed OE specifications, which will be an ideal choice to replace your broken parts.
- The Auto Parts Zone brand showcases replacement gas lift supports that are easy to install and restore peace of mind within minutes. Auto Parts Zone Struts (i.e. topper struts) feature hardened chromium-plated steel shafts for durability, self-cleaning pistons to reduce contamination, and patented temperature compensation module valves for consistent operation even in extreme weather conditions. With the Auto Parts Zone brand, you can find the right lift support to lift and hold up your vehicle component whether it’s the back glass, hatch back, hood, liftgate, tailgate, trunk lid, or a universal lift support.
- Also supply a variety of mortor parts, such as ABS sensor, door handle, cooling fan, ERG value, water pump, window regular, blower assembly, fuel pump, ignition coil, belt tensioner assembly, valve cover, thermostat assembly, TPMS sensor, VTT Valve, timing chain kit, hub bearing assembly etc.....
Specification:
Product information:
Placement on Vehicle: Tonneau Cover Left & Right
Extended Length[in]:29.5"
Compressed Length[in]:17.5"
Reference Number: PM2048,716821,SE1200M80PS100
Only Fits
Extended Length [in] 29.5
Compressed Length [in] 17.5
Ext.ser.num 378N
Force (lbs) 85.00
Ball Socket Long Cup (Steel) Type=13mm=1/2"=.50"
Ball Socket Long Cup (Steel) Type=13mm=1/2"=.50"
Uses include Automotive, Truck, Industrial, Marine, ATV Vehicles, Household cabinets, RV Vehicles and many other applications.
Placement on Vehicle: Tonneau Cover Left & Right
Extended Length[in]:29.5"
Compressed Length[in]:17.5"
Reference Number: PM2048,716821,SE1200M80PS100
Only Fits
Extended Length [in] 29.5
Compressed Length [in] 17.5
Ext.ser.num 378N
Force (lbs) 85.00
Ball Socket Long Cup (Steel) Type=13mm=1/2"=.50"
Ball Socket Long Cup (Steel) Type=13mm=1/2"=.50"
Uses include Automotive, Truck, Industrial, Marine, ATV Vehicles, Household cabinets, RV Vehicles and many other applications.
Interior Technology:
- Highest corrosion resistance achieved through powder coated cyclinders and special treated piston rod surfaces.
- Minimal friction for the production of lowest extension forces.
- Great life cycles.
- Protection against vibration and light side forces.
- Integrated grease chamber.
- Low break away forces.
- Installation and storage in any position.
Easy to install:
- Find Someone or Props hold the hatch, hood or rear window open while replacing the lift support, so that they can raise or lower it as needed.
- Before removing the old lift supports, inspect the end connections and compare them the the units on your vehicle to make sure that they are the same as well as the extended length.
- Remove the lift support struts retaining clips by using a flat head screwdriver.
- Slowly turn the screw driver and it will lift up the retaining clips. Then pull the support away from the vehicle and it will release.
- To install the new supports do the same procedure in the reverse. DO NOT jam the new support end over the ball socket without lifting the retaining clips slightly damage may occur.
- Push the strut onto the ball joint. Place the strut over the ball joint and use your tool to apply pressure until it pops into place.
- Move the Props to see whether the supports work good.
Attention:
- Please check the descriptions and compatibility chart to ensure that the replacement fits your auto before your purchasing.
- The lift supports with strong force can't be pressed by hand. Please use appropriate shop manual for your vehicle to obtain specific service instruction. If you do not have an installation manual or not enough skill to install this part, it is recommended to seek the help from a qualified machanic.
Rear Glass Window Strut Display 
Hatch Strut Display 
Front Hood Strut Display 
Trunk Product Display