Introduction:
Compression Mode, Support 4CH real-time 720P Million Pixels AHD input and Analog Standard Definition camera input, or 2CH HD input + 2CH SD input;
Exclusive pre-allocate DVR Special File System Technology, Solving repeatedly wipe cause file fragmentation, solving SD card file system collapse, data loss and cannot find SD card and file garbled, ensure the integrity of the data.
8-33V Adaptive Wide Voltage input, Super Low Power Consumption Design;
SD card storage (maximum support 128GB SD card. )
It can be completely resist car Vibration,Dust and others cause data corruption; Support GPS/BD/G-SENSOR ;
High Reliability Aviation plugs,High Cost Performance with reliable stability,simple and clear operation menu .
Features-Recorder:
No-seam recording technology.
Support SD card (is not included) up to 128GB, more convenient and vibration-proof than hard disk version.
Support four channel 4pin connector video and audio input, one channel AV connector video and audio output.
Support IR remote control.
Special design of encrption to protect recording files.
Support wide range of voltage input from 8V to 33V.
Feature-Cameras:
Features:
- High-definition and wide viewing angle
- Ballhead design so that you can adjust the camera to any angel you need
- 24 IR LED light
- PAL video system
- Resolution: 720P (1 million pixels)
- Applicable to variety of vehicles: car, truck, RV, mini-van etc
- Perfectly solve the issue of bad car rear view effect ,can help reduce incidents and accidents
- Image sensor: CMOS
- Minimum illumination: 0.1Lux/ F1.2 (0 Lux with IR on)
- White balance: auto
- Video output: RCA connector, 1.0Vp-p, 75ohm
- Power supply: DC 12V
- Operating temperature: -20°C~ 75°C, RH95% Max
- Storage temperature: -40°C ~ 85°C, RH90% Max
Specifications:
Compatible with: apply to all kinds of cars
Operating language: Chinese/English
Password safe: user password and administrator password two-class administration
Video input: 4ch
Video output: 1ch
Video standard: PAL, NTSC
Video format: AVI
Image compression: H.264
Audio input: 4ch port
Audio output: 1ch port
Image format: CIF/HD1/D1
Recording storage: SD card
Built-in accelerometer G - Sensor: support
Power input: 8-36V
Power output: 12V
Working temperature: -40℃-80℃
Note:
Please confirm that the battery voltage is between 8V-36V. If surpass the range, it would burn the equipment.
Package List:
1 * SW-001A 720P AHD Mobile DVR Kit
4 * 720P (1 million pixels) 24 IR LED Night Vision CCTV Camera
2 * 3M Video Power Cable
2 * 5M Video Power Cable
What included in the package are as showed on the picture of this listing
Common problem
Q:When Device issue appear,you are confused on how to solve it.
A:Check Device Item No & Firmware Version,sent back to us with detail description of issue.Our Technical Team will handle it.
More detail you described,easier for us to solve it quickly.
Q:Video Output Lost
A:1.Check situation of DVR:Device Input Power;Power Cable Connection;GND Connect to battery;fuse;RED & Yellow Cable of Power must connect together;
2.Check the Screen Power or Check if the Screen change to related AV Channel;
3.Check the connection of Video Output & Screen Cable;
Q:Device keep Rebooting
A:1)Check working power,if low power device will keep rebooting;
2)HDD/SD Card error, remove storage device and turn on device checking;
Q: If the video input interface of the device and camera is different.
A:The DVR is using 4 needle type port, the camera is BNC port or Aviation, if it is different, please use the X-over to connect, or connect according to the DVR Line sequence definition
Q:Device on with HDD but not recording;
A:1)Check SD/HDD if format;if not please enter Main GUI--System Set--Format,format HDD/SD Card;
2)If close Recording ,or set Timed Recording mode, if yes it won’t recording if not the time set
3)If the HDD is connect well, if the HDD/SD light is on.
Q: Video files lost, or there is no video files at a certain period time.
A: 1. Analysis the lost video and ensure the lost time period.
2.Confirm if the DVR was opened at that time, such as crashed midway park, loading and unloading ect. And the device didn’t set the delay recording
Q: Can not control the Car PTZ, can not rotate to all direction.
A: If the agreement and Baud rate of the PTZ is setting right,if the address code is corresponding, if the video channel is setting to max when control the PTZ. Like if is control the first channel, then must set the first channel image to be max.
2.GPS related FAQ
Q: With GPS but no GPS coordinate Information
A:1)Check if GPS module exist;
2)Check GPS Antenna connection,suggest install on the outside place with strong signal;
3)If testing in office, suggest put GPS Antenna out of window;
4)If working environment not good will related to no GPS Information or wrong information;
Q:Deviation of GPS Location on Map?
A:The signal is effective if the GPS module has been positioning, there are so many reasons caused bias, government restriction, permissible error, GPS signal break off, The actual satellite map error occurred for the security, GPS Correction can solve the problem.
3G Wireless Module related FAQ
Q:If using 3G ,what should we concern?
A:1)Choose inside wireless module WCDMA,EVDO,TD-SCDMA, relative module setting is different then SIM Card is different, please make sure the module is corresponding with the SIM Card.
2)If Server IP & Port set correct,if 3G signal strong for dialing;3G dialing successfully or not;
3)Check 3G Antenna connection,dialing will be failed if 3G signal too weak;
4)Check SIM Card 3G Flow
Q:When meet device offline or no video,what should be done first?
A:1)Press INFO key to enter the system Info page,check if SIM Card exist,3G signal and dialing status,Antenna connection,Check SIM Card 3G Flow,change to a new SIM Card check again;
2)3G Signal strong but dialing fail,check if center IP & Port set correct;
3)Check if Device ID already be occupied;
Q:3G Signal is intermittent, video get stuck ?
A:At present, signal coverage of the WCDMA and EVDO is very wide, but still there are some mountain area signal is weak, this will influence. Then check if the frame rate in Sub-stream setting is too high.
Q:WIFI Signal 60/100,connect failure;
A:General condition, connection is no problem when the signal intensity up to 60/100 if WIFI setup are right. If the device can not be found in LAN, then you should check if setting SSID and password, IP Address, besides, check the Encryption Type and authentication mode if setting according to requirements.
Client Software FAQ
Q:Device working but can not see Vehicle and video on client software
A: 1)Check if Center Server running and device Number if using;
2)Check Server IP and Port parameter setting;
3)Check is using 3G or WIFI for connecting, if 3G check the 3G Model WCDMA or EVDO and related SIM card,3G antenna connect normally/APN setting/Center No. setting;
If it still can not work,please offer the most detailed information to us for technical support
Q:Device Online but can not see video
A:1)Please set Low Sub-stream,when sub-stream set high it will effect the transmission because of the network;
2)Network environment not good;
Q: Device works well in the Client, but cannot see the video a period time later.
A:1.Check if connect to server successfully on device, if dialing probably SIM Card no 3G Flow,change another SIM card for testing;
2.Check if Device Number be changed,if yes,need add device to server again;
3.If still can not view video after previous 2 steps,please check if 3G module error;
Other related questions
Q: Video Lost in certain channel?
A: Possible reasons are as follows
1. This channel has no video input
2.The camera of this channel breaks down or work abnormality
3.If the camera takes an electricity power from the equipment directly, may be the
equipment’s electric voltage isn't enough to make camera work as usual;
d) The cable that links this channel has problem
Q: Can’t playback files on PC successfully?
A: Possible reason is as follows:
1.Have never chosen a record file or document path; please choose the path that records file first before playback.
Q: Remote control not works?
A: Probably of the reasons are as follows:
1.The remote control didn't pack battery;
2.2.The remote control damages;
3.Device damages.
Q: During playback, the map doesn't show?
A: Possible reasons are as follows: Net cable did not connect to PC; Net works, but the computer can not get to the Internet;
Q: When SD card and HDD records, How is the record coverage?
A: SD card and HDD will record circularly for each other. When they are full, they will delete the original video records respectively.
