|
|



















Police Military Grade Lipstick Size Digital Lens Eye Camera.
1- PRO-550 RES RAGECAM MICRO MINI COLOR CCD TUBE CAM
34ft Of power video cable With RCA male-Female & Male Power outputs
6mm(78 degrees)+
8mm(58 degrees) Lenses
(OR PICK ONE FROM THE LIST BELOW)
The Best Dynamite MICRO MINI Quality waterproof bullet cam to date!

(PICK YOUR OWN LENSES INSTALLED BONUS) IF YOU WANT A 2.8mm, 3.6, 4, 4.3, 6, 8, 12, OR 16mm LENS WE WILL INSTALL IT FREE FOR YOU, JUST SPECIFY IN THE NOTES TO SELLER BOX WHEN PAYING WITH PAYPAL & ALSO EMAIL US THROUGH EBAY SO WE CAN NOTE THAT FOR YOU. OTHERWISE 3.6MM WILL BE SENT BY DEFAULT AUTOMATICALLY. YOU CAN ALSO MACRO VIEW & USE THIS CAMERA TO FOCUS WITHIN AN INCH OR LESS LIKE A MICROSCOPE FOR EXTREME CLOSE UP ON CIRCUIT BOARDS OR ANYTHING!
PICK YOUR LENS VIEW, & WE WILL INSTALL IT FOR YOU FREE ON THIS AMAZING MINI CAM, YOU MUST SPECIFY IN YOUR PAYPAL PAYMENT NOTES TO SELLER WHAT LENS YOU WANT OK, OR 3.6MM WILL BE SENT BY DEFAULT, OR PURCHASE ADDITIONAL LENSES & EASILY CHANGE THEM YOURSELF.
16 other specialty lenses available in our ebay store for any view needed FROM WIDE FISH EYE TO NARROW TELEPHOTO
COOL DEAL
(616)205-5440 
We carry the widest selection of additional bullet cam lenses available!
Field Of View Calculations:
(Extreme wide angle fish eye view) 1.2mm lens has approximate 185 degree field of view (will fit with the lens cover off)
1.78mm lens has approximate 170 degree field of view (will fit with the lens cover off)
2.8mm lens has approximate 130 degree field of view (will fit with the lens cover off)
3.6mm lens has approximate 92 degree field of view
8mm lens has approximate 58 degree field of view
50mm lens has approximate 7.8 degree field of view (will fit with the lens cover off)(License plate close up at 150ft)

1- Soft Mount Headband/ REMOVABLE Velcro Nylon Sleeve Holster 
1-Mini
Soft Mount Quick Clip Locking Position Adhesive Grip Holder Mounts to
any flat surface quickly & also with a very secure hold/grip.


19MM CLIP INCLUDED ONLY WITH 1/4"-20 THREAD FOR USE ON A TRIPOD.
WOW 19MM DIAMETER


1
& 3/4 INCH HARD REAR MOUNT Omni pan tilt swivel mount base with
screws, or you can use reclosable tape for the bottom round base &
mount to any flat surface & will allow adjustable pan/tilt view in
seconds, the securely lock down the wing not. NOTE:
THE PINCH SNAP CLIP ABOVE WILL THREAD ON TO THIS OMNI PAN TILT MOUNT
& ALSO OUR ROLL BAR & SUCION CUP MOUNTS SOLD IN OUR EBAY STORE.
2 Zip Tie adhesive Flat Bottom FRONT/BACK mounts for anywhere quick mounting.
1-Direct DC Pigtail wire harness for *optional vehicle direct wire to the battery or fuse box(Note:
If you are not sure how to wire this to your fuse box, you can probably
take it over to a stereo installation place & tell them you need
the pigtail wired into your fuse box so when you start your car, the
camera will power also, or you could keep it powered all the time
unless you physically disconnect it from the pigtail to power down. +POS -NEG to
run the mic which then shares power with the camera without having to
splice into the finished 2.5mm DC connection on the cam or mics.
1-8aa battery holder for back up Any Double AA battery power.
NOTE:
Only use good aa STD or Rechargeable batteries with atleast a 1500mah
rating, no mix & match cheap junk half drained, or low mah rated rechargeables
Use Duracell Copper top or Energizer for the best results.
TIP: If your bullet cam appears to be blank screen or rainbow lines through the video, change the batteries.

WARNING: Do
not overpay & get BURNED - hosed or taken by companies/sellers
claiming selling knockoff hong kong crap.







Need security???
This cam is Dynamite
Field Of View Calculations:

After twisting off the lens cap protector, Use a eyeglass flathead type screwdriver to loosen the little grub set screw located in the threads of the bullet cam head, then twist out the lens, & twist in the replacement lens. Focus to infinity while twisting in. When in perfect focus, using both hands, 1 holding the bullet cam & lens in place while the other gently tightens the set screw to hold focus.
Lens change instructions for bullet-dome & board cameras:
Screw off the lens cap cover, & you will expose the lens. Looking at the camera from a side view is a small hole located in the threads. Using a regular head eyeglass type screwdriver, loosen that set screw counter clockwise just enough to enable removal of the lens by unscrewing it from the barrel. If you loosen it too much, the set screw may fall out, & get lost (very tiny). Now twist in the new lens, & focus it while you twist it in. when it is focused, with your left hand, hold the lens in place pushing in on it to keep it focused perfectly. With your right hand gently tighten the set screw just enough until it locks the lens into place. Do not overtighten the set screw or you may strip it. Now screw the cap back on to seal the lens waterproofing it. IF YOUR BULLET CAM DOES NOT POWER UP, OR GOES TO RAINBOW LINES, THAT MEANS THE BATTERIES ARE LOW. REPLACE THEM OR RECHARGE YOUR PACK.
INSURED SHIPPING WITH TRACKING# INCLUDED
Time and
Money searching for lower cost cameras. We have some of the best pricing, & service available.
Since
1998! Quality Video Components Professionally Does Licensed Camera,
& Network Digital Video Recording DVR Installations with many
Nationwide, & Local references, serving Grand Rapids - Sparta -
Belding - Greenville - Ionia - Cedar Springs - Rockford - Kentwood
- Wyoming - Grandville - Caledonia - Holland - Hudsonville - South
Haven - Muskegon - Kalamazoo - Manistee - Traverse City - Cadillac -
Big Rapids, & All of West Michigan BE Careful, or you may get Snow-Balled!
WE
BOUGHT
& TESTED THAT SO CALLED 580 RES. CAM & IT WAS ONLY 420
RES. 1/4" CCD & TERRIBLE IN LOW LIGHT, PLUS, THE LENS WAS NOT WIDE
ANGLE, & IT HAD NO IMAGE STABILIZATION BECAUSE OF THE NARROW VIEW,
& NOT A TRUE EX-VIEW CHIP,
& THE CARRY CASE WAS CHEAP HONG KONG GEAR.
TRUST NOBODY!!!!