Pair Front Air Suspension Struts Fits Mercedes 4MATIC W222 S550 S450 S500 L S560

Note:

  • 1 year warranty for any manufacture defect.Please provide photos or videos to apply for warranty.

Please inspect this part carefully prior to installation and contact us with any questions BEFORE attempting to install it.

 

Use For The Following Vehicles :

Mercedes-Benz S-Class W222

Mercedes-Benz Maybach S550 2017
Mercedes-Benz Maybach S560 2018-2020
Mercedes-Benz S450 2018-2020
Mercedes-Benz S500 2015
Mercedes-BenzS500L 2017-2018
Mercedes-Benz S550 2014-2017
Mercedes-BenzS560 2018-2020

 

Replacement Part Number

2223208113,2223204913,222-320-4913, 
222-320-8113, 222 320 4913, 222 320 8113, 
A2223204913, A2223208113, A222-320-4913, 
A222-320-8113, A222 320 4913, A222 320 8113

 

Package Includes: 

  •  Pair for Front Left and Right Air Suspension Shock Struts

 

Generation & Evolution:

Mercedes-Benz S-Class
W116 First generation (1972-1980)
W126 Second generation (1980-1991)
W140 Third generation (1991-1998)
W220 Fourth generation (1999-2005)
W221 Fifth generation (2006-2013)

W222 Sixth generation (2014-present)

 

Air suspension strut Removal Guideline:

Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.

To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.

Consult your vehicle owner's manual,service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.

Once the vehicle has been raised from the ground, put vehicle in neutral, and then back into park to release the tension on the drivetrain.

1.Raise vehicle at lifting points prescribed by manufacturer

2. Remove applicable engine baytrimto gain accesstothetop strut mount. 

3.Slowly disconnect air line fitting fromthetop ofthe strut. 

4.Remove used air line fitting from the air line and discard. use the figure below as an example. 

5.Remove front left wheel.

6.Disconnect the two (2) electrical connectors from the strut. 

7.Unroute the lines and disconnect the strut wire harness from the lower mount of the

strut.

8.Remove lower strut bolt and nut. 

9.Remove the three (3) top mount nuts. 

10.Remove bolt and nut from spindle and disconnect. 

11.Remove the strut from the vehicle. 

12.Remove top mount plate from the strut. this will be reused in the installation. 

13.Removal complete.

 

Air Suspension Strut Installation Guideline:

1.Removethe shipping plug fromthe check valve and install the voss fitting from the provided accessory kit on to the arnott air strut. remove the    shipping pin from the voss fitting. 

2.Install the top mount plate on to the new strut. 

3.Install the arnott strut in the vehicle. 

4.Reconnect the spindle to install the bolt and nut. tighten to manufacturer’s

specifications. 

5.Reinstall the bottom mount bolt and nut. tighten to manufacturer’s specifications.

6.Install the three (3) top mount nuts provided in the accessory kit. tighten to manufacturer’s specifications.

7.Connect the two (2) electrical connectors to the new strut solenoid.

8.Reinstall the strut wire harness using the provided zip tie and reroute the lines.

9.Push the air line into the air fitting on the top of the strut until it is fully sealed/seated

10.Reinstall the applicable engine bay trim.

11.Reinstall the front left wheel.

12.Inflate the air strut per manufacturer’s specifications.

13.Lower the vehicle.

14.Installation complete.

 

Attention??
- Please double confirm the compatibility as well as the OEM number before purchasing.
- These air suspension solenoid valves are aftermarket parts. They will replace the original ones.
- If you are not sure whether our parts fit you should contact us before buying,we will confirm for you.
- Instruction is not included. Professional installation is recommended.
- Contact us please for whatever we can help. 

 

Features:
1. Brand new & high quality aftermarket product
2. Durably built and precisely engineered for improved vehicle control
3. Fully tested to ensure a proper fit and performance
4. Safe, easy installation
5. An economical option to restore your vehicle's suspension

 

Professional Installation Recommended??

We recommended you install the part by yourself, it will reduce much labor cost. if you are not professional, please ask your mechanic to fix it.

 

Strict Quality Control??
All of our PARTS undergo strict quality control throughout the production process. During each step of production multiple quality control checks are performed to insure each and every part lasts for years to come.

PushAuction