Features:

Product precautions:

1. This product uses low-voltage DC 12V-24V to work, and must be connected to a switching power supply. It is prohibited to directly connect to 220V, otherwise the controller may be damaged. 2. The input port has polarity (positive and negative), and reverse connection is prohibited. The wiring should be performed in a power-off state. After the wiring is completed, the installation and lighting connection should be checked for correctness before powering on. If the DC voltage wiring or lighting installation is incorrect, a short circuit may occur, causing the controller to malfunction. 3. This product is only suitable for use in a dry indoor environment. Strong wind, high temperature or severe vibration may cause sensor failure.

4. The sensing angle is 120 degrees, the sensing distance is 1-3 meters, and the sensor is most sensitive when facing people 5. AB sensing heads should be arranged according to the site settings.

Additional operating instructions:

1. If the AB sensors are triggered simultaneously within 6 seconds, the light strip will run inward from both ends. If the AB sensors are triggered continuously for more than 6 seconds, the light strip will preferentially run in the direction of the first triggered sensor

2. Set the light chasing time:

3. Single, double, three, four, five

4. If the induction continues during the delay period, the light strip remains on = the total time from A to B + delay time.

5. Short circuit for protection device: In the short circuit state, the status indicator light will flash.

Connection way:

Insert the LED light strip into the control port corresponding to the stair steps in turn for connection. For example:

> Step 1, the positive pole of the lamp into the [orange] terminal marked with number 1, and the negative pole into the [green] terminal marked with number 1;> Step 2, the positive pole of the lamp into the [orange] terminal marked with number 2, and the negative pole into the [green] terminal marked with number 2; Step 3, the positive pole of the lamp into the [orange] terminal marked with number 3, and the negative pole into the [green] terminal marked with number 3; ... and so on.

The control host has 32 ports, please connect the required light strips in according to actual needs. Unused ports can be ignored. If necessary, you can add additional light strips later.

instructions:

Long press [Key 1] for 4 seconds: Enter the mode of setting the number of stepping lights. Then short press [Key 1] to light up  indicator from "1-32". Select the desired number of stepping light channels according to the lighted indicator, and then long press [Key 1] again or wait for 5 seconds to save the setting.

Short press [Key 1]: Switch between 5 lighting modes. Select the desired mode according to the indicator display.

Short press [Key2]: Select constant light duration: 10s-20s-40s-80s-100s. "Long press [Key2] for 4 seconds: Enter stair light brightness selection mode. Then short press [Key2] to select brightness level: "10%-20%-40%-60%-." Long press [Key2] again or wait for 5 seconds to save the setting.

Short press [Key3]: Set stair light flow , time options: "0.3s-0.5s-0.8s-1.0s-1.2s. ”

No key activity within 5 seconds: All lights will flash once, indicating that all settings have been automatically saved.

Specifications:

Part name: Staircase LED controller > Product model: UL1032

Input voltage: DC12v/24V

Sensor head: 2 (A/B)

Size: 180*85*20mm

Color: white

Material: abs

Package contents:

1 LED driver.

2 sensors.

2 output lines

Note:

1:Due to manual measurement, there may be 1-2cm error, please make sure you do not mind before ordering.

2:Due to the difference between different monitors, the image may not reflect the actual color of the item

Payment must be completed within 5 days. If you have any problems about payment, please contact us via message.

We only ship to confirmed Order addresses. Please comfirm that your Order for address is in line with your shipping for address.

Please kindly note that the combined shipping is not provided because the shipping fee is calculated by weight. Also, the each additional item means exactly the the same color and size. 

It takes about 7-15 working days to US; about 10-30 working days to other countries.  for transit time may be a little delayed because of the bad weather and customs inspection. If you do not receive your item within 30 working days since payment finished, please contact us immediately for further assistance.

We strive for customer satisfaction! Positive is very important to us. If you have any questions, please feel free to contact us via "Ask seller a question" . We will reply your email within 24 working hours.