3000VA pure sine wave inverter and 120A battery charger in one unit, for 12V systems
A combined inverter and battery charger for 12V battery systems. It gives 3000VA of 230V AC output, charges at up to 120A from shore power or a generator, and supports PowerAssist, UPS changeover and VE.Bus system integration.


Not included, sold separately: VE.Bus to USB interface – needed to configure charge parameters and system settings with VEConfigure software. GX device (for example Cerbo GX or Color Control GX) – for local and remote monitoring and control through the VRM app and portal.
Clean sine wave 230V output and fast charging of a large 12V battery bank, without a separate charger.
Adds battery power when shore or generator supply runs short, and takes over in under 20 milliseconds if the supply fails.
Parallel or three-phase operation, ESS systems and remote monitoring with a GX device.
The Victron MultiPlus 12/3000/120-16 is a multifunctional inverter with an AC charger in one compact unit. It combines a true sine wave inverter with an adaptive battery charger, plus PowerAssist technology and system integration via VE.Bus.
It is designed for 12V battery systems that need 3000VA of AC output at 230V. It suits off-grid installations, marine and vehicle applications, and backup power systems where a reliable, high-capacity inverter charger is needed in a compact form.
The MultiPlus 12/3000/120-16 combines a pure sine wave inverter with a high-current multi-stage battery charger. When AC input is available (shore power or a generator), the unit charges the battery bank and passes power through to connected loads. When AC input is lost or disconnected, it switches to inverter mode automatically. The 120A charge current is substantial for a 12V system and lets a large battery bank be charged efficiently without a separate charger.
The 16A AC input current limit reflects the unit's intended use where the available AC supply is limited, such as a 16A shore power connection on a boat or a small generator. PowerAssist is particularly useful here: if connected loads draw more than the incoming AC can supply, the MultiPlus draws the shortfall from the battery rather than tripping the supply breaker. This lets a modest AC input support peak loads that would otherwise exceed its rating.
VE.Bus connectivity means the unit can be monitored and configured through Victron GX devices such as the Color Control GX or Cerbo GX. Multiple units can be connected in parallel for more capacity, or configured for split-phase or three-phase output. Configuration is done with VEConfigure software via a VE.Bus to USB interface (sold separately).
The MultiPlus prevents overload on limited AC sources such as a generator or shore power. If demand rises, it first reduces charging, then boosts the available output by adding power from the battery. This helps keep your loads running smoothly without tripping the supply.
The MultiPlus is a core building block in Victron ESS systems. It can be combined with MPPT solar chargers or grid-tie PV inverters to create a flexible self-consumption and backup power system.
If the grid fails or generator power disconnects, the inverter takes over automatically in less than 20 milliseconds, keeping computers and sensitive equipment running without interruption.
With a GX device (for example Cerbo GX), you can monitor and control your system locally (LAN) or remotely over the internet using the free VRM app and VRM portal. This suits off-grid systems, backup power and professional installations.
Installation should be carried out by a qualified electrician or accredited installer with experience of DC and AC electrical systems. The MultiPlus must be connected to a suitably rated 12V battery bank with correctly sized DC cabling and fusing. For any grid-connected or shore-power use in the UK, make sure the installation complies with current wiring regulations (BS 7671) and any network operator requirements.
Setting charge parameters and system settings needs VEConfigure software and a VE.Bus to USB interface, which are not included. For lithium battery installations, check compatibility and set the right battery protection settings before commissioning.
| Model | MultiPlus 12/3000/120-16 230V VE.Bus |
|---|---|
| Part number | PMP122300001 |
| Barcode (EAN) | 8719076045151 |
| AC input voltage range | 187-250V AC |
|---|---|
| AC input frequency | 50/60Hz |
| Transfer switch rating | 16A |
| AC input current limit | 16A |
| Battery voltage | 12V DC |
|---|---|
| DC input voltage range | 9.5-17V DC |
| AC output voltage | 230V AC ± 2% |
| AC output frequency | 50Hz ± 0.1% (adjustable to 60Hz) |
| Rated output | 3000VA |
| Continuous output power (25°C) | 2400W |
| Continuous output power (40°C) | 2200W |
| Continuous output power (65°C) | 1700W |
| Peak power | 6000W |
| Maximum continuous output current | 11A |
| Maximum efficiency | 93% |
| Zero load power | 20W |
| Zero load power (AES mode) | 15W |
| Zero load power (Search mode) | 8W |
| Maximum output fault current | 32A peak (1 second) |
| AC input voltage range (charger) | 187-265V AC |
|---|---|
| AC input frequency (charger) | 45-65Hz |
| Power factor (charger) | 1 |
| Charge voltage (absorption) | 14.4V DC |
| Charge voltage (float) | 13.8V DC |
| Storage mode | 13.2V DC |
| Charge current (house battery) | 120A |
| Charge current (starter battery) | 4A |
| Battery temperature sensor | Yes |
| PowerControl / PowerAssist | Yes / Yes |
|---|---|
| Auxiliary output | Yes (16A) |
| Programmable relay | Yes |
| Communication | VE.Bus: parallel and three-phase operation, remote monitoring, system integration |
| Remote on/off | Yes |
| Operating temperature | -40°C to +65°C (fan-assisted cooling) |
| Maximum altitude | 2000m |
| Enclosure | Aluminium, blue (RAL 5012) |
|---|---|
| Protection rating | IP20 |
| Dimensions (H x W x D) | 362 x 258 x 218mm |
| Weight | 18.85kg |
| Packed weight | 20.9kg |
| Carton size (H x W x L) | 290 x 450 x 330mm |
| Country of origin | India |
| Safety | EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1 |
|---|---|
| Emission / immunity | EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3 |
| Road vehicles | ECE R10-4 |
If your item develops a fault, message us through eBay with your order and a short description or photo of the fault. We arrange the return of faulty items at our cost, test the item, and repair or replace it if it is faulty and within the manufacturer's warranty.