FMA 14290 Ni-MH / Ni-Cd Rechargeable Battery Pack

Keep your personal care devices running at peak performance. FMA's 14290-cell battery packs are precision-built for electric razors, shavers, trimmers, and electric toothbrushes — available in Ni-MH (700mAh) and Ni-Cd (500mAh) chemistry, in 2-cell (2.4V) or 3-cell (3.6V) configurations. Custom connector arrangements available on request.

Product Specifications

• Battery System: Ni-MH or Ni-Cd Rechargeable
• Cell Model: 14290 (14.0 × 29.0 mm)
• Nominal Voltage: 2.4V (2SL) or 3.6V (3SL)
• Ni-MH Capacity: 700mAh
• Ni-Cd Capacity: 500mAh
• Cell Package: PVC Heat-Shrink Wrap
• Condition: Brand New
• Brand: FMA

Variant Overview

• Ni-MH 2SL – 2.4V 700mAh (2 cells in series)
• Ni-MH 3SL – 3.6V 700mAh (3 cells in series)
• Ni-Cd 2SL – 2.4V 500mAh (2 cells in series)
• Ni-Cd 3SL – 3.6V 500mAh (3 cells in series)

Package Contents

• 1 × Battery Pack (type and configuration as selected)

Compatible Applications

• Electric razors & shavers
• Hair trimmers & clippers
• Electric toothbrushes
• Small personal care appliances requiring 2.4V or 3.6V Ni-MH/Ni-Cd packs

Installation Guide

Required Skills: Basic DIY ability; comfort with opening small appliances and handling soldered or plug-in connectors. No advanced electronics knowledge required for plug-in type replacements. Soldering skill needed if the original pack is wire-soldered.

1. Power off the device — ensure the appliance is switched off and unplugged from any charging base before opening.
2. Open the battery compartment — use a suitable screwdriver (usually Phillips #00 or #0) to remove the back cover or battery access panel.
3. Remove the old battery pack — carefully disconnect the connector or, if soldered, note the wire polarity (+ / −) before desoldering.
4. Verify voltage and connector match — confirm the replacement pack voltage (2.4V or 3.6V) and connector type match your device’s original specification.
5. Connect the new pack — plug in the connector or solder the wires, observing correct polarity. Red = positive (+), Black = negative (−).
6. Reassemble and test — replace the cover, secure all screws, then place the device on its charger for a full initial charge cycle before use.

Important Notes

• ⚠️ Verify compatibility before ordering — check your device’s original battery voltage, capacity, and connector type. When in doubt, contact us with your device model number.
• ⚠️ Do not mix chemistries — never mix Ni-MH and Ni-Cd cells in the same pack or use a Ni-Cd charger on a Ni-MH pack, and vice versa.
• ⚠️ Polarity must be correct — reversed polarity will damage the device and may cause the battery to overheat.
• ⚠️ Custom connector available — if your device uses a non-standard connector or cell arrangement, contact us before purchase so we can configure the pack correctly.
• ⚠️ Initial charge recommended — fully charge the new pack before first use to achieve rated capacity.
• ⚠️ Not suitable for direct primary-cell replacement — this is a rechargeable pack; it must be used with a compatible charging circuit inside the device.

Custom Connector Options

Need a specific connector type or cell arrangement? Contact us with your requirements and we will configure the pack to match your device.

Safety Information

• Charging: Use only a compatible Ni-MH or Ni-Cd charger. Never charge unattended or near flammable materials.
• Storage: Store in a cool, dry place (10–25 °C / 50–77 °F). Keep away from direct sunlight and moisture.
• Operation: Do not short-circuit, disassemble, crush, or incinerate.
• Temperature: Charge: 0–45 °C; Discharge: −20–60 °C.
• Disposal: Recycle in accordance with local regulations. Do not dispose of in household waste.
• Inspection: Discontinue use if the pack shows leakage, swelling, or unusual heat.

Shipping & Transportation Notice

• Ni-MH/Ni-Cd battery packs are classified as hazardous materials for transport purposes.
• Air shipment may be subject to restrictions; ground or sea freight is recommended for bulk orders.
• All packages are securely packed to meet international dangerous goods regulations.
• Delivery times may vary due to customs clearance and carrier regulations.
• Required documentation (MSDS / SDS) is available upon request.