Please contract us firstly if there are any problems when you received the package. We will definitely give you satisfying solution, please don't leave neutral or negative feedback without any communication.

Note:

1. Item Is Soft Material, And If Car Has A Large Rear Curvature With An Excessively Bent Tail, Requiring Cut & Manual Adjustment Of The Product's Bend When Installing

2. Item model and Compatibility Table are just a reference, take size as a fitment standard.
   In order to avoid to choose Wrong Size item ,please measure car size before purchasing according our size photo.
   Make sure the length if you want before you buy,thanks.

The product is made of elastic PU material, which can be bent and adjusted freely.
If it is too long during installation, you need to cut by yourself according to the length of your car. If you mind, please do not purchase.
Thank you for your understanding.

Note:
Wrong size for chrysler 300c 2007
Wrong size for BMW 2008 328xi

Not for Audi A5 Quattro 2011 Cabriolet Convertible 2-Door 2.0L 1984CC 121Cu. In. l4 GAS DOHC Turbocharged

Not for Hyundai i30n 2023 
Not for Audi S5 Premium Plus Convertible 2-Door 2015

Not for INFINITI G37 2009 Sport Sedan 4-Door 3.7L 3696CC V6 GAS DOHC Naturally Aspirated

Not for Ford Expedition EL XLT Sport Utility 4-Door 3.5L 3496CC 213Cu. In. V6 GAS DOHC Turbocharged 2017 

Not for Honda Civic LX Coupe 2-Door 1.8L 1799CC l4 GAS SOHC Naturally Aspirated 2015 

Not for Benz S550 Base Sedan 4-Door 4.7L 4663CC 285Cu. In. V8 GAS DOHC Turbocharged 2013

Not for Chrysler 300c Sedan 4-Door 5.7L 345Cu. In. V8 GAS OHV Naturally Aspirated  2007
Not for Genesis G70 Base Sedan 4-Door 2025
Not for Ford Fusion SE Sedan 2018
Not for Toyota Avalon Limited Sedan 2011

Features:

1.Flexible and lightweight PU install in minutes using ultra strong automotive tape
2.No special installation , no drilling or screws required.
3.Gives your ride a more aggressive and customized look.
4.Protect your car from scratches/bump and any undesired damage caused by a collision.
5.This rubber lip is very flexible and can fit to different types of trunk or roof It comes with double side tape on the back for easy installation.

Specifications:
Material: PU Rubber

Size: 1.18-1.38M Adjustable(The product can be trimmed to fit the rear of the car in its own curvature)

Color: Glossy Black
Fitment: Universal Car
Position: Car Spoiler/Roof/Hatch Gate/Trunk/Bonnet

Package Included:
1 Set Car Rear Wing Sticker

Attention:
Measure the length of the rear wing of the car and cut the product according to the length of the rear wing;
1. Simulated installation
Don't tear off the adhesive first, place the product on the car and compare and adjust it to the accurate position.
2 Surface treatment
(1) Cleaning
Use a towel dipped in alcohol or clean the vehicle body with clean water in the area that needs to be installed.
(2) Precautions
Before installation, the vehicle body must be kept dry and free of dust, oil, and wax. When the temperature is below 15 degrees Celsius, it is necessary to heat the adhesive on the vehicle body and product. (Heating with a hair dryer is sufficient)
(3) Installation
Tear off a corner of the protective film on the back of the product, leave the film on the outside to match the installation position, and then slowly remove and press the film.
(4) Protection period
Within 48 hours after the installation of the product (at the adhesive position), it should not come into contact with water, oil, or large dust

Note:
1.Please allow some color and measurement errors due to manual and monitor factors.