CONFLAT SOLUTIONS | SILVER STANDARD AUDIT | ANC-600CF-RLM100-4XKF25-USED
TECHNICAL_LOG: V7.2_ANCORP_600CF_RLM100_4XKF25 BUILD_SESSION: 2026.11.20.ANC_600CF_RLM100_4XKF25_USED

ANCORP 6.00″ CF SERVICE END-PLATE W/ HOLLOW 1.00″ ROTARY-LINEAR MANIPULATOR & QUAD (4×) KF25 PORTS

6.00″ CF (DN100CF / NW100CF) // CNC FEEDTHROUGH TOWER // 1.00″ (25.56 MM) OD HOLLOW SHAFT (10.00″ VACUUM EXTENSION) // 3× RADIAL + 1× SHAFT-END KF25 / NW25 (4× TOTAL) // AUDITED USED
🔍 FORENSIC METROLOGY & SUBCOMPONENT INSPECTION DISCLOSURE

DIMENSIONAL & HARDWARE AUDIT: Verified via digital caliper and scale metrology across all subcomponents. Includes the CNC-machined 6.00″ ConFlat (DN100CF / NW100CF) service end-plate (16× clearance thru-holes), tall atmospheric feedthrough column housing three (3×) welded radial KF25 / NW25 (40.02 mm flange OD) ports at 90° intervals—each complete with stainless blanking cap, elastomer centering ring, and aluminum wing-nut clamp—plus dual knurled brass/bronze dynamic compression gland nuts (7.125″ to 8.50″ above the 6.00″ CF flange face). The precision-ground 25.56 mm (1.006″ / nominal 1.00″ OD) hollow stainless steel rotary-linear shaft spans ~9.75″ on the atmospheric side and reaches 10.00″ (254.0 mm) full extension on the vacuum side (~20.50″ combined shaft length). Its atmospheric end terminates in a fourth (4th) integrated KF25 / NW25 (40.02 mm OD) line-of-sight flange opening straight down the hollow shaft bore to the central-bore circular stainless sample platen disc fitted with four (4×) axial fasteners/standoffs. Note: Any copper gasket shown seated on the 6.00″ CF knife-edge in inspection photography is for knife-edge protection/staging only; install a fresh OFE copper gasket prior to UHV pumpdown, and inspect/lubricate internal dynamic shaft seals with Krytox®/Apiezon® UHV grease.

DISCLOSURE: Any pedestal, mounting stand, lab post, or positioning stem visible in product staging photography is deployed strictly for demonstration and photographic support purposes and is NOT included in the sale of this artifact.

Forensic Technical Specification Brochure

Forensic Specification Parameter Verified Component Metric
Manufacturer (OEM)A&N Corporation (ANCORP — Williston, Florida, USA) Vacuum Hardware Architecture
Assigned Audit SKUANC-600CF-RLM100-4XKF25-USED (Complete Hollow-Shaft Service End-Plate & Quad KF25 Assembly)
Primary Chamber Interface6.00″ OD ConFlat (DN100CF / NW100CF / 5.970″ [151.6 mm] OD) w/ Atmospheric Feedthrough Tower
Primary Flange Bolting Geometry16× Clearance Thru-Holes (0.332″ ID for 5/16″-24 UNF Hardware / BCD: 5.128″ [130.3 mm])
Sample Manipulation SubsystemHeavy-Duty Precision-Ground Hollow Rotary-Linear Shaft w/ Dual Knurled Compression Seal Collars
Manipulator Shaft Diameter (Caliper)25.56 mm (1.006″ / Nominal 1.00″ OD) Hollow Precision-Ground Stainless Steel Shaft
Manipulator Shaft Axial Span & Stroke~9.75″ Atmospheric Side + 10.00″ (254.0 mm) Full Vacuum Extension (~20.50″ Combined Total Length)
Terminal Atmospheric Shaft Port (#4)Integrated Axial KF25 / NW25 (40.02 mm OD) Flange on Hollow Shaft Tip for Direct Line-of-Sight Pass-Through
Terminal Vacuum Sample PlatenCentral-Bore Circular Stainless Platen Disc Fitted w/ Four (4×) Axial Screws/Standoffs
Dynamic Seals & Gland ArchitectureDual Knurled Brass/Bronze Compression Gland Nuts (~0.75″ each; 7.125″–8.50″ above flange)
Auxiliary Tower Foreline Ports (#1–#3)Three (3×) Welded Radial KF25 / NW25 (40.02 mm OD) Ports (90° Spacing) w/ 3× Blanks, Rings & Wing Clamps
Total KF25 / NW25 Port CountFour (4×) Total KF25 / NW25 Flanges (3× Radial Tower Ports + 1× Axial Hollow-Shaft Tip Flange)
Structural Metallurgy & FinishAISI 304 / 304L Vacuum-Grade CNC-Machined Stainless Steel (Passivated; Brass/Bronze Gland Nuts)
Operational Vacuum PerformanceHigh Vacuum to Ultra-High Vacuum (HV / UHV) Load-Lock & Process Regime (10⁻³ to 10⁻⁹ Torr)
Helium Mass Spec Leak TightnessDesigned for ≤ 1 × 10⁻⁹ atm·cc/sec Across Dynamic Shaft Seal & KF25 Elastomer Interfaces
Thermal Bakeout DynamicsUp to 150 °C – 200 °C Continuous (Governed by Dynamic Shaft Elastomer & KF25 Viton® Ring Limits)
Primary Process CapabilityIn-Situ Optical/Laser Line-of-Sight Diagnostics, ALD Precursor Dosing, Load-Lock Transfer & Roughing
Condition DesignationAUDITED USED (Sharp 6.00″ CF Knife-Edge / Smooth 25.56 mm Ground Shaft / Complete w/ 3× KF25 Sets)
Manufacturer (OEM)A&N Corp (ANCORP)
Primary Flange6.00" CF (DN100 / NW100)
Manipulator TypeHollow Rotary-Linear Shaft
Shaft OD (Caliper)25.56 mm (1.006" / 1" Nom)
Full Vacuum Extension10.00" (254.0 mm) Stroke
Vacuum Platen EndBored Disc w/ 4× Screws
Total KF25 / NW25 Ports4× Total (3× Radial + 1× Shaft)
Shaft-Tip Port (#4)Axial KF25 Line-of-Sight
KF25 Hardware Included3× Wing Clamps, Rings, Blanks
Dynamic Seal CollarDual Knurled Brass/Bronze
Max Bakeout Temp150–200 °C (Elastomer Limit)
Condition StandardAudited USED (Complete)

Hardware Status Matrix

Tier 1: Audited NOS / Zero-Hour Unissued Factory Reserve.
Not Applicable
Tier 2: Seller Refurbished Rebuilt & Resurfaced Assembly.
Not Applicable
Tier 3: Audited USED (Complete) Caliper-Audited / 10″ Hollow Stroke / 4× KF25.
✔ CURRENT STATUS
BLUE DIAMOND PROTECTION PROTOCOL: ACTIVE

TOP RATED PROTECTION: This listing qualifies for Free 30-Day Domestic Returns and is backed by our 30-Day Mechanical Integrity Warranty. Sold in bench-vetted, caliper-verified AUDITED USED condition featuring a sharp, continuous 6.00″ CF (DN100CF / NW100CF) knife-edge, smooth 25.56 mm hollow precision-ground rotary-linear stainless shaft (10.00″ full vacuum extension / ~20.50″ total span) terminating in an axial KF25 / NW25 line-of-sight flange on the atmospheric end and a central-bore platen disc with 4× axial fasteners on the vacuum end, dual knurled brass/bronze compression gland nuts, and three (3×) welded radial KF25 / NW25 tower ports complete with stainless blanking caps, centering rings, and wing-nut clamps. Per eBay Seller Protection policy for Top Rated Plus members, any item returned in a condition different from the original shipment (including but not limited to: damaged 6.00″ CF knife-edge, scored or bent 25.56 mm hollow ground shaft, missing KF25/NW25 clamps/rings/blanks or gland hardware, thermal over-baking >200 °C damaging elastomer seals, or process/atmospheric contamination) will result in an automatic, mandatory 50% refund deduction to account for the permanent loss in verified institutional UHV utility.