DC 12V 24V 30A RF High Power WaterProof Switch 433MHz Wireless Remote Control Switch Transmit 1000M for Water Pump LED Fan
Description:
Product Advantages
30A High-Power Switch Module
The working voltage is DC 8-80 V, and the maximum current is 30A. Equipment capable of carrying 400W high power makes the receiver more widely used. The current of 10A is no longer sufficient, but 30A can meet this requirement very well.Easy to connect
There are only V+ and V- wires at the input and output terminals. You only need to find the correct wire port to connect. The operation is simple.433 Wireless radio frequency remote control
The remote control uses RF433MHz, 1527 learning code/2262 fixed code, and powerful chip functions. It is waterproof and can still be used normally after being splashed with water.Long Distance Launch
The transmitting distance in an open outdoor area can reach 1000M.3 Programmable Modes
There are 2 programmable modes: Momentary mode, Toggle mode, Latched mode. You can change the programming according to your own preferences, easy to operate.IP65 WaterProof Rating
The switch adopts a closed design and is not afraid of outdoor rain. Comes with hot-melt wiring tube, which can make the wiring more perfectly sealed and waterproof after hot-melting.
One receiver can be paired with multiple remote controls, and one remote control can be paired with multiple receivers
One receiver supports storing approximately 20 remote controls, and one remote control can control approximately 3 receivers to achieve diverse controls.Various application scenarios
Can be applied to homes, farms, factories, offices, supermarkets and other places. Can be used to connect lights, electric fans and other household equipment and electrical equipment.
Product Features
Special design, can be well waterproofed:
The receiver is IP65 waterproof and adopts a closed design. The hot melt method is used at the wiring joint to provide better waterproofing and better convenience for users.
30A High Power, Wide range of product applications:
Products can be used in homes, farms, factories, offices, laboratories, supermarkets, etc.
Remote control water pump\fan\table lamp\LED light\bulb\ventilator\signal transmission.....
Remote control water pump\fan\table lamp\LED light\bulb\ventilator\signal transmission.....
Stable Signal , Anti-interference:
The maximum control distance can be up to 1000 meters in open areas ..
Receiver and remote control enable multiple controls:
One remote control can control one receiver.
One receiver can store the data of approximately 20 remote controls, and one remote control can control approximately 3 receivers.
One receiver can store the data of approximately 20 remote controls, and one remote control can control approximately 3 receivers.
Simple Wiring
Parameter:
RF433mhz High-Power Wireless Receiver
Working voltage : DC 8-80V
Max current : 30A
RF frequency : 433MHz
Working temperature : -30~+80
Receiving Sensitivity : >97dbm
Amount of storage remote controls : about 20 pieces
Support encoding : 1527 leaning code/ 2262 fixed code
RF Operating mode : ASK superheterodyne wireless reception
Size: 47*29*93mm
Max current : 30A
RF frequency : 433MHz
Working temperature : -30~+80
Receiving Sensitivity : >97dbm
Amount of storage remote controls : about 20 pieces
Support encoding : 1527 leaning code/ 2262 fixed code
RF Operating mode : ASK superheterodyne wireless reception
Size: 47*29*93mm
RF433mhz Remote Control
Support encoding : 1527 Leaning code/ 2262 fixed code
Remote distance : up to 50m or 1000m (theoretical distance)
Battery : 1 pcs 23A 12V(included) or 1 pcs CR2032 (included)
RF frequency : 433MHz
Size: 97*40*16 mm or 60*30*13 mm
Intelligent DIY control methods
*Momentary Mode*
1. Press and hold the button, The device will turn ON .
2. Release the button, The device will turn OFF.
2. Release the button, The device will turn OFF.
*Toggle Mode*
1. Pressthe button once,The device will turn ON .
2. Pressthe button again,The device will turn OFF.
*Latched Mode*
2. Pressthe button again,The device will turn OFF.
*Latched Mode*
1. Pressthe "ON" button, The device will turn ON .
2. Pressthe "OFF" button, The device will turn OFF.
Signal pairing
2. Pressthe "OFF" button, The device will turn OFF.
Signal pairing
Note
1. When you receive our products, it may set in one remote mode randomly, that because each product was tested before it can be arranged to shipment. So, please delete the existing data to first use.
2. After deleted the data, all the remote controls cannot work any more.
2. After deleted the data, all the remote controls cannot work any more.
Clear data:
Press the learn button (on the receiver) 8 times until the light flashes. All data is deleted.
