🔧 Rear Height Level Sensor — 6 Pin, Direct Replacement — For Land Rover Range Rover Sport I L320 (2005‑2013) — Replaces AH32‑5B732‑AD, LR014587, LR023650

Is your Range Rover Sport I sitting unevenly? Seeing suspension fault warnings on the dash, or the air suspension refusing to raise or lower? A failed ride height sensor is one of the most common causes — it sends incorrect levelling data to the ECU, triggering error codes and knocking out your dynamic drive system. Don't pay main dealer prices for a replacement. This brand‑new, OE‑spec height sensor bolts straight in, restoring accurate height readings and getting your suspension working properly again.

⚠️ IMPORTANT — READ BEFORE BUYING

The vehicle list below is a guide only. Always match the part numbers on your existing sensor with those shown here before ordering. If you're unsure, send us your UK registration number or VIN and we'll confirm the correct part for your vehicle. No instructions are included — professional fitting is recommended.

✅ Key Features

• 🚗 Direct Fit Replacement — Engineered to the same dimensions and 6‑pin connector layout as the original Land Rover sensor. Drops straight into the rear mounting point without modification or rewiring.

• 🔌 Exact 6‑Pin Connector — Matches the factory plug for a secure, reliable electrical connection. No splicing, no soldering, no bodge jobs.

• 🛠️ Restores Dynamic Drive & Variable Damping — Accurate height sensing is critical for vehicles equipped with both dynamic drive and continuous variable damping. This sensor feeds the correct data to the suspension ECU, clearing fault codes and returning a smooth, level ride.

• 💪 100% Brand New & High Quality — Fresh from the factory, not a refurbished or second‑hand unit. Robust housing resists corrosion, road salt, and the harsh underside environment.

• 🔄 Fits Either Rear Side — Designed for the rear left or right side on UK right‑hand drive (RHD) models. One part covers both positions, so you can replace the faulty side without guessing.

⚙️ Specifications

• Condition: 100% Brand New

• Product Name: Height Level Sensor (Ride Height Sensor)

• Model: Ride Height Level Sensor

• Location: Rear Side

• Placement on Vehicle (UK RHD): Rear — Left OR Right Side

• Terminal Quantity: 6 Pins

• Fitment Type: Direct Replacement

🔢 Part Numbers

Please confirm your original sensor carries one of these numbers before purchasing:

• AH32‑5B732‑AD

• AH325B732AD

• LR014587

• LR023650

🚗 Vehicle Fitment

✅ This sensor fits the following vehicle only when equipped with dynamic drive AND continuous variable damping:

Land Rover Range Rover Sport I (L320) — 2005 to 2013

💡 Critical Fitment Note

• This sensor is only for the L320 generation (2005–2013). It will not fit the later L494 (2013‑onwards) models.

• Your vehicle must have both dynamic drive and continuous variable damping. If your Sport doesn't have these factory options, this sensor will not be correct.

• The above list is a guide. Always cross‑reference your existing part number with the numbers above. If in doubt, message us with your reg or VIN before you buy.

📦 Package Includes

• 1 × Rear Left / Right Height Level Sensor (6‑pin, as described)

⚠️ Installation & Notes

• No Instructions Included — Fitting typically involves raising the vehicle, removing the wheel/arch liner for access, unplugging the old sensor, and bolting the new one in place. If you're not confident working under a vehicle, have a qualified mechanic handle the install.

• Calibration May Be Required — After fitting a new height sensor, some vehicles need a suspension calibration or ride‑height reset using diagnostic software to clear fault codes and set the reference point. Check your workshop manual or speak to your installer.

• Inspect Adjacent Components — While you're there, check the sensor linkage arm and mounting brackets for wear or damage. A bent linkage can cause the same fault symptoms even with a new sensor.

✅ Why UK Land Rover Owners Choose This Sensor

• Fix Suspension Faults Properly — No more "Suspension Fault" messages on start‑up or uneven ride height. A working sensor keeps your Range Rover Sport riding as it should.

• Dealer Alternative — Main dealer prices for an OE sensor plus labour can be eye‑watering. This OE‑spec part gives you the same result for a fraction of the cost.

• Peace of Mind — Brand new, not used. No worn internal potentiometer or corroded pins.

• VIN Verification — Send us your reg or VIN and we'll double‑check fitment before dispatch, saving you the hassle of returns.

👉 Add to basket today, confirm your part number, and get your Range Rover Sport's suspension back to factory‑fresh performance!