2x (Coppia) Cerniere COMPLETE Giradischi Technics Cappa Coperchio
2x (Pair) Hinges COMPLETE Technics Turntable Dust Cover Lid
OK PER (OK FOR):
SL-1200 da MK2 in poi...
SL-1200 from MK2 onwards...
TI CONSIGLIO DI LEGGERE ATTENTAMENTE !!!
I ADVISE YOU TO READ CAREFULLY !!!
- QUESTO KIT NON VA BENE PER MK1
- QUESTO KIT NON VA BENE PER MK2 DAL 1979 AL 1984
(INTERASSE FORI FISSAGGIO STAFFE AL GIRADISCHI 43mm)
Se hai un 1200 MK2 dal 1979 al 1984 e quindi con interasse fori fissaggio staffe al giradischi di 43mm, vedi questa inserzione: https://www.ebay.it/itm/365613575277
In alcune foto si vede l'installazione su un 1700 mk2.
Sul 1200 Mk2 Mk3 Mk4 Mk5 Mk6 Mk3d e' uguale. Stesso identico risultato !!
CON QUESTE CERNIERE PUOI SFILARE IL COPERCHIO IN UN SECONDO.
SONO ISPIRATE ALLE CERNIERE ORIGINALI DEL SL-1200MK2.
RICAMBIO NON ORIGINALE
NON CI SONO MOLLE
STAMPATO 3D IN ALTA DEFINIZIONE CON MATERIALE TECNICO IPER RESISTENTE
FOTO REALI
COLORE NERO
**** CON QUESTE CERNIERE IL COPERCHIO RIMARRA' APARTO A 76°, IN APPOGGIO, PER VIA DI UN FONDOCORSA SULLA CERNIERA.
76° VUOL DIRE UN PO PRIMA DEL VERTICALE. OVVIAMENTE SI PUO ANCHE CHIUDERE.
Un
semplice studio sul baricentro e sul punto di massima apertura non
permette al coperchio di chiudersi "da solo" involontariamente, nemmeno
sotto urti "sfortunati".
Nel
caso che il tuo modello di giradischi ha la "target light / pop-up
light", cioe la luce che premendola sale su, e' consigliabile chiuderla
(tenerla bassa) prima di chiudere il coperchio.
In
commercio potrai trovare un progetto simile ai miei ma attenzione che
e' il proggeto base, ovvero senza nessuna vite e con apertura coperchio
esagerata, oltre i 95°, in oltre, il coperchio, non si puo sfilare allo
stesso modo. Informati prima di acquistare.
>>> ENGLISH VERSION <<<
- THIS KIT DOES NOT FIT MK1
- THIS KIT DOES NOT FIT MK2 FROM 1979 TO 1984
(TURNTABLE BRACKET FIXING HOLES INTERAXIS 43mm)
If you have a 1200 MK2 from 1979 to 1984 and therefore with a turntable bracket fixing hole interaxis of 43mm, see this listing: https://www.ebay.it/itm/365613572380
In some photos you can see the installation on a 1700 mk2.
On the 1200 Mk2 Mk3 Mk4 Mk5 Mk6 Mk3d it is the same. Same exact result !!
WITH THESE HINGES YOU CAN REMOVE THE COVER IN A SECOND.
THEY ARE INSPIRED BY THE ORIGINAL SL-1200MK2 HINGES.
NON-ORIGINAL SPARE PART
THERE ARE NO SPRINGS
3D PRINTED IN HIGH DEFINITION WITH HYPER RESISTANT TECHNICAL MATERIAL
REAL PHOTOS
BLACK COLOR
**** WITH THESE HINGES THE LID WILL REMAIN OPEN AT 76° BECAUSE THERE IS AN END STOP ON THE HINGE.
76° MEANS A LITTLE BEFORE THE VERTICAL. OBVIOUSLY YOU CAN ALSO CLOSE.
A
simple study of the center of gravity and the point of maximum opening
prevents the lid from closing "by itself" involuntarily, not even under
"unfortunate" knocks.
In case your turntable model has the "target light / pop-up light", that is the light that when pressed goes up, it is advisable to close it (keep it low) before closing the lid.
On the market you can find a project similar to mine but be careful that it is the basic project, that is without any screws and with an exaggerated lid opening, over 95°, in addition, the lid cannot be removed in the same way. Get informed before buying.