sunhans wireless signal amplifier is suitable for home/office and public places, suitable for wireless aircraft model/aerial photography, wireless monitoring equipment.

Product parameters:

Model: SH24BTA

Support standard: IEEE802.11 B/G/N
2500 MHz frequency: 2400 -2500MHz
Impedance: 50Ω
RF output power: 3000MW [35dBm]
Transmitter gain: 13-17dB
Receiver gain: 8 - 12dB
Noise factor: 3.0dB (typical value)
Operating temperature: -40°C to +70°C
Operating humidity: up to 95°
Casing: aluminum
Weight: 400g
Dimensions: 6.5X3.0×1.5cm

Usage:

1. Remove the antenna on the wireless AP or wireless router first.

2. Take out the SMA cable (RG316) and connect the wireless AP (wireless router or wireless network card) to the TO Radio port of the signal amplifier.
3. Connect the antenna to the other end of the signal amplifier (TO Antenna).
4. Plug in the power supply and you are done.

Product features

1. Increase wireless network coverage and stability;

2. Support 2.4G B/B+/G/N super G wireless network and Bluetooth devices, frequency range 2400-2500MHz internationally recognized industrial frequency band;

3. The maximum output power is 3W (35dBm,), bidirectional, half-duplex and automatic switching (plug and play), automatic gain control;

4. SMA connector, convenient for replacing various antennas, can connect indoor and outdoor directional and omnidirectional antennas;

5. Can be used with Bluetooth devices, wireless network cards, wireless routers, wireless APs;

6. The input level is unlimited, even if the input power is high, it will not burn;

7. Made of all-aluminum alloy, easy to dissipate heat;

8. Simple and convenient installation, no software required, plug and play;

Using methods

1. Remove the antenna on the wireless AP or wireless router first.

2. Take out the SMA cable (RG316) and connect the wireless AP (wireless router or wireless network card) to the TO Radio port of the signal amplifier.

3. Connect the antenna to the other end of the signal amplifier (TO Antenna).

4. Plug in the power supply and you are done

common problem
1. How much can the signal be amplified by adding this product?
Answer: The power of our ordinary household wireless router is generally 80-100mW (milliwatts). After adding this product, the maximum output power can reach 2500mW (milliwatts). You can imagine the effect and function of adding this product to your own environment!

2. What kind of wireless products can support this product?
A: Our products support 2.4GHz WLAN 802.11b, 802.11b+, 802.11g, 802.11b+g+N, wireless 2.4G AP, 2.4G wireless bridge, 2.4G wireless router, 2.4G wireless network card, 2.4G wireless monitoring, 2.4G wireless microphone, 2.4G Bluetooth device, etc.

3. 3. Can the router be encrypted after adding this product?

A: Any encryption such as WEP/WPA/WPA2 can be supported!

4. Is this product suitable for outdoor use?

A: This product cannot be placed outdoors! But it can be installed in a waterproof box!

5. How big is the difference between 2.4bg and 2.4bgN?

Answer: The maximum transmission rate of 2.4BG is 54MB, but the maximum transmission rate of 2.4BGN is 150MB. The relative bandwidth is much better than BG. The premise is that your router must support BGN specification router to achieve it. If you use a BG specification router, the maximum output is still 54MB.

6. Special Notes:

Answer: The power amplifier is not suitable for use on high-power devices, because high-power products themselves will output high power. If installed on this product, it will cause the equipment to saturate and distort the signal, which is counterproductive. It is strongly recommended to use it on devices that output low power. The effect is better and more obvious.


DataCaciques