Application

For 2011-2022 Jeep Grand Cherokee WK2 2WD 4WD

**Does NOT Fit models with Air-Ride Suspension
**Stock strut top nuts need to be cut short to allow installation of spacers.

 

Description

Lift Height: 2.5 inch Front

Spacer Thickness: 1.57 inch (40 mm)

Material: Steel

Package Included: 2x Strut Spacers

 

Note: With an independent suspension, the amount of lift can be significantly greater than the thickness of the lift spacer.

Calculating the amount of lift to expect for an independent suspension application can be a little less straightforward. Independent suspension designs typically consist of at least one control arm, the inside of which is secured to the frame while the outside is attached to the wheel. It is supported by a spring or strut mounted someplace between the wheel and the frame. Suspension travel is accomplished by the control arm pivoting at the point where it is mounted to the frame. Since the wheel is mounted farther from the control arm pivot than the strut is, it experiences a longer travel than the strut does. For example, installing a 1.5” thick strut spacer on independently suspended vehicles can act as 3” lift kits.

 

What are strut spacers?
The most common application for strut spacers is with stock trucks. Many customers use them to lift the front-end, and level out the overall stance of the vehicle. If you simply want to increase the available ground clearance in a cost effective manner coil strut spacers are for you. One other advantage of coil strut spacers is the fact they won’t alter the ride characteristics of your factory suspension, and they are easy to install at home with basic hand tools and mechanical knowledge.

 

Installation

1. Park vehicle on a level surface and chock rear wheels. Jack up the front of the vehicle and place jack stands under the frame rails.

2. Remove the tires and wheels.

3. Remove the ABS line and bracket from the upper control arm.

4. Disconnect driver and passenger side sway bar end links.

5. Remove lower strut mounting bolts.

6. Pry up ABS retaining clips from the upper strut mounting nuts.

7. Remove upper strut mounting nuts.

8. Remove entire strut assembly from vehicle

9. Place strut spacer on top of strut.

10. Loosen upper ball joint nut. Do not remove from knuckle.

11. Using a hammer, hit the side of your knuckle to separate ball joint from it.

12. Place a jack under your lower control arm to support and remove your upper ball joint.

13. Lower suspension slightly and reinstall strut assembly using the new hardware provided in your kit.

14. Once installed, jack up your suspension from your lower control arm

15. Using a pry bar on your upper control arm, Place ball joint back into knuckle

16. Tighten upper ball joint to factory torque spec.

17. Reattach ABS line and bracket and sway bar end links

18. Take vehicle to an alignment shop to avoid improper tire wear and poor ride quality.

 

 

 

 

 

 

 

 

 

Item Specifics
Brand	PARTHIGH
Manufacturer Part Number	PART135109HK
Package Included	2X Strut Spacers
Placement on Vehicle	Front Left Right
Lift Height	2.5" Front
Actual Thickness	appr. 1.57 in./ 40 mm
Spacers Specs	2.5 inch Lift Height / 1.57 inch (40 mm) Thickness
Item Note	Lift amount does NOT equal spacer thickness
Drive Type	2WD 4WD
OE Spec or Performance/Custom	Performance/Custom
Adjustable	No
Part Type	Suspension Lift Kit
Kit or Single Part	Kit
Ship from	CA
Fitment Type	Direct Replacement
Material	Steel
Surface Finish	Corrosion / Oxidation Resistant
Included Hardware	Mounting Hardware
Color	Black
Interchange Part Number	For 2011-2022 Jeep Grand Cherokee WK2 2WD 4WD
Fitment Note	Does NOT Fit models with Air-Ride Suspension
Installation Attention	The Top Nuts of Stock Strut need to be cut short
Tire Recommendation	Run up to 33in tires