Carbon Brushes 0.55x0.35x3.31 Inch for Electric Motors Power Tool, 4 Pack
What is this?
The carbon brush is cut from hard carbon material with high wear resistance. The raw material is block graphite. It is an important component of electric motors and power tools, use in rotary tool, rotary hammer drill, cut-off saw, circular saw, generator and axle machine, etc.
What will I get?
Package Content: 4pcs Motor Carbon Brushes; Total Length: 45mm/ 1.77 inch; Carbon Brush Size(LxWxH): 14x9x6mm/ 0.55x0.35x3.31 inch
Are there any advantages of the product?
The carbon brush cuts smoothly, and the copper wire is tight and does not easy to fall off. It has high wear resistance, good reversing performance, good conductivity, heat conduction and lubrication performance, and has certain mechanical strength, which has long service life.
How to use it?
The carbon brush is used on the commutator or slip ring of the motor as a sliding contact to lead in the current. It is clamped on the metal bracket and pressed onto the shaft by a spring.
What should I notice?
Tip: If you replace the carbon brush with a new one, it is found that the carbon brush has been worn or half worn within a few minutes or hours of use, indicating that your shaft rotor is in off-normal working state, and you need to replace the shaft rotor in time.
The carbon brush is cut from hard carbon material with high wear resistance. The raw material is block graphite. It is an important component of electric motors and power tools, use in rotary tool, rotary hammer drill, cut-off saw, circular saw, generator and axle machine, etc.
What will I get?
Package Content: 4pcs Motor Carbon Brushes; Total Length: 45mm/ 1.77 inch; Carbon Brush Size(LxWxH): 14x9x6mm/ 0.55x0.35x3.31 inch
Are there any advantages of the product?
The carbon brush cuts smoothly, and the copper wire is tight and does not easy to fall off. It has high wear resistance, good reversing performance, good conductivity, heat conduction and lubrication performance, and has certain mechanical strength, which has long service life.
How to use it?
The carbon brush is used on the commutator or slip ring of the motor as a sliding contact to lead in the current. It is clamped on the metal bracket and pressed onto the shaft by a spring.
What should I notice?
Tip: If you replace the carbon brush with a new one, it is found that the carbon brush has been worn or half worn within a few minutes or hours of use, indicating that your shaft rotor is in off-normal working state, and you need to replace the shaft rotor in time.
Hot Item
- 1.We accept eBay payment .
- 2.Payment must be received within 7 business days of auction closing.
- 1.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
- 2.Items will be shipped within 1-3 business day when we received payment.
- 3.Delivery time depends on destination and other factors.
Carbon Brushes 0.55x0.35x3.31 Inch for Electric Motors Power Tool, 4 Pack
What is this?
The carbon brush is cut from hard carbon material with high wear resistance. The raw material is block graphite. It is an important component of electric motors and power tools, use in rotary tool, rotary hammer drill, cut-off saw, circular saw, generator and axle machine, etc.
What will I get?
Package Content: 4pcs Motor Carbon Brushes; Total Length: 45mm/ 1.77 inch; Carbon Brush Size(LxWxH): 14x9x6mm/ 0.55x0.35x3.31 inch
Are there any advantages of the product?
The carbon brush cuts smoothly, and the copper wire is tight and does not easy to fall off. It has high wear resistance, good reversing performance, good conductivity, heat conduction and lubrication performance, and has certain mechanical strength, which has long service life.
How to use it?
The carbon brush is used on the commutator or slip ring of the motor as a sliding contact to lead in the current. It is clamped on the metal bracket and pressed onto the shaft by a spring.
What should I notice?
Tip: If you replace the carbon brush with a new one, it is found that the carbon brush has been worn or half worn within a few minutes or hours of use, indicating that your shaft rotor is in off-normal working state, and you need to replace the shaft rotor in time.
The carbon brush is cut from hard carbon material with high wear resistance. The raw material is block graphite. It is an important component of electric motors and power tools, use in rotary tool, rotary hammer drill, cut-off saw, circular saw, generator and axle machine, etc.
What will I get?
Package Content: 4pcs Motor Carbon Brushes; Total Length: 45mm/ 1.77 inch; Carbon Brush Size(LxWxH): 14x9x6mm/ 0.55x0.35x3.31 inch
Are there any advantages of the product?
The carbon brush cuts smoothly, and the copper wire is tight and does not easy to fall off. It has high wear resistance, good reversing performance, good conductivity, heat conduction and lubrication performance, and has certain mechanical strength, which has long service life.
How to use it?
The carbon brush is used on the commutator or slip ring of the motor as a sliding contact to lead in the current. It is clamped on the metal bracket and pressed onto the shaft by a spring.
What should I notice?
Tip: If you replace the carbon brush with a new one, it is found that the carbon brush has been worn or half worn within a few minutes or hours of use, indicating that your shaft rotor is in off-normal working state, and you need to replace the shaft rotor in time.
Hot Item
- 1.We accept eBay payment .
- 2.Payment must be received within 7 business days of auction closing.
- 1.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
- 2.Items will be shipped within 1-3 business day when we received payment.
- 3.Delivery time depends on destination and other factors.